LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2014 >> LR4 Base, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel & Console -- LR4/L319 >> Instrument Panel And Console >> Instrument Panel >> Removal And Installation >> Installation

Removal And Installation: Installation

  1. With assistance, install the instrument panel.
    • Tighten the Torx bolts to 25 Nm (18 lb.ft).
  2. Passenger side: Install the heater housing to bulkhead Torx bolt and tighten to 6 Nm (4 lb.ft).
  3. Driver side: Install the heater housing to bulkhead Torx bolt and tighten to 6 Nm (4 lb.ft).
  4. Connect the instrument panel center reinforcement fibre optic cables.
  5. Connect the instrument panel center reinforcement electrical connectors.
  6. Connect the CJB electrical connectors.
  7. Connect the heater motor electrical connector.
  8. Connect the electrical connectors to the passenger side lower A-pillar.
  9. Connect the ground cables to the passenger side lower A-pillar.
    • Tighten the nuts to 10 Nm (7 lb.ft).
  10. Connect the electrical connectors to the driver side lower A-pillar.
  11. Connect the ground cables to the driver side lower A-pillar.
    • Tighten the nuts to 10 Nm (7 lb.ft).
  12. Install the adapter panels.
    • Tighten the nuts to 10 Nm (7 lb.ft).
  13. Secure the A/C lines to the bulkhead.
    • Clean the components.
    • Install new O-ring seals.
    • Tighten the bolt to 10 Nm (7 lb.ft).
  14. Secure the A/C lines to the body.
    • Tighten the nuts to 10 Nm (7 lb.ft).
  15. Connect the bulkhead heater hoses.
  16. Install the instrument panel carrier to bulkhead Torx bolt and tighten to 25 Nm (18 lb.ft).
  17. Install the plenum chamber panel.

    For additional information, refer to: Plenum Chamber .

  18. Install the instrument panel upper section to body bolt and tighten to 10 Nm (7 lb.ft).
  19. Install the speaker grille.
    • Secure with the clips.
  20. Install the instrument panel center bracket Torx bolts and tighten to 25 Nm (18 lb.ft).
  21. Attach the heater housing center ducts.
  22. Connect the drain tubes to the heater housing.
  23. Connect the steering column intermediate shaft.
    • Install the special bolt and tighten the new nut to 22 Nm (16 lb.ft).
  24. Install the transmission selector lever.
    • Tighten the bolts to 10 Nm (7 lb.ft).
  25. Attach the transmission selector lever cable.
    • Install the clip.
  26. Install the front seats.

    For additional information, refer to: Front Row Seat .

  27. With assistance, install the door assembly.
    • Connect the electrical connector.
    • Secure the electrical connector.
    • Secure the grommet.
    • Tighten the bolts to 10 Nm (7 lb.ft).
  28. Attach the door check strap to the A pillar.
    • Tighten the Torx bolts to 10 Nm (7 lb.ft).
  29. Install the driver side closing trim panel.
    • Connect the electrical connector.
    • Secure the clip.
    • Tighten the screws.
  30. Install the passenger side closing trim panel.
    • Connect the electrical connector.
    • Secure the clip.
    • Tighten the screws.
  31. Install the cowl side trim panels.

    For additional information, refer to: Cowl Side Trim Panel .

  32. Install the floor console.

    For additional information, refer to: Floor Console .

  33. Refill the cooling system.

    For additional information, refer to: COOLING SYSTEM PARTIAL DRAINING AND VACUUM FILLING

  34. Recharge the A/C system.

    For additional information, refer to: Air Conditioning System Recovery, Evacuation and Charging .

  35. Install the engine cover.

    For additional information, Refer to: Engine Cover - V6 S/C 3.0L Petrol /

scientia non olet · About LEMON Manuals