LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2020 >> Soul GT Line Turbo >> Repair and Diagnosis >> External Pages >> Different car >> Section 45 (Abs/ESC Diagnosis) >> DTC C1235-01: Pressure Sensor (Primary) - Electrical >> Component Inspection >> Inspection Procedure

Inspection Procedure

WARNING: This page is about a different car, the 2021 Kia Soul. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition "OFF".
  2. Connect KDS to "Data Link connector (DLC)".
  3. Ignition "ON".
  4. Select "Diagnostic Trouble Codes (DTCs)" mode.
  5. Using a KDS, Clear DTC.
  6. Operate the vehicle within DTC Detecting Condition in General Information.
  7. Select "Diagnostic Trouble Codes (DTCs)" mode again.
  8. Is the same DTC stored in the system?

    Good 

    • Fault might be intermittent and caused either by poor contact in connectors or wiring harness, or it has been repaired and control module memory is not cleared yet. Thoroughly check terminal of battery, all connectors (and connections) for looseness, bending, corrosion, contamination, deterioration, and/or damage.
    • Repair or replace as necessary and then go to "Verification of Repair " procedure.

    No Good 

    • Carefully re-do this troubleshooting guide steps.
    • If no problems were found with the circuits or connectors, replace the ESC and go to "Verification of Repair " procedure.

    * In case of replacing ESC, perform following "Vehicle S/W Management" procedures

CAUTION: In case of replacing ESC, perform following procedures.
Inspection Condition Inspection Procedure Reference
  1. Auto Detected Configuration Reset (ESP (ESC) Only).
  2. Ignition "ON".
  1. Connect KDS to "Data Link connector (DLC)".
  2. Perform "Auto Detected Configuration Reset (ESP(ESC) Only)" in "Vehicle S/W management" with KDS.
 Fig.1 to 4
G13285624Courtesy of KIA MOTORS AMERICA, INC.
G13285625Courtesy of KIA MOTORS AMERICA, INC.
G13285626Courtesy of KIA MOTORS AMERICA, INC.
G13285627Courtesy of KIA MOTORS AMERICA, INC.
Inspection Condition Inspection Procedure Reference
  1. Variant Coding.
  2. Ignition "ON".
  1. Connect KDS to "Data Link connector (DLC)".
  2. Perform "Variant Coding" in "Vehicle S/W management" with KDS.
 Fig.1 to 6
G13285628Courtesy of KIA MOTORS AMERICA, INC.
G13285629Courtesy of KIA MOTORS AMERICA, INC.
G13285630Courtesy of KIA MOTORS AMERICA, INC.
G13285631Courtesy of KIA MOTORS AMERICA, INC.
G13285632Courtesy of KIA MOTORS AMERICA, INC.
G13285633Courtesy of KIA MOTORS AMERICA, INC.
Inspection Condition Inspection Procedure Reference
  1. Longitudinal G-sensor Calibration (HAC/DBC Only).
  2. Ignition "ON".
  1. Connect KDS to "Data Link connector (DLC)".
  2. Perform "Longitudinal G-sensor Calibration (HAC/DBC Only)" in "Vehicle S/W management" with KDS.
 Fig.1 to 5
G13285634Courtesy of KIA MOTORS AMERICA, INC.
G13285635Courtesy of KIA MOTORS AMERICA, INC.
G13285636Courtesy of KIA MOTORS AMERICA, INC.
G13285637Courtesy of KIA MOTORS AMERICA, INC.
G13285638Courtesy of KIA MOTORS AMERICA, INC.
scientia non olet · About LEMON Manuals