LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2015 >> Forte LX, Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Indicators & Gauges >> Instrument Cluster >> Repair Procedures >> Inspection

Repair Procedures: Inspection

  1. Check point (Warning indicator)
    NO Ref Symbol Color Name Signal Input Signal Control (Unit/Sensor) Check Point
    1
    G09744334
    		 Green Turn Left C-CAN BCM 1. CAN line failure
    2
    G09744335
    		 Green Turn Right C-CAN
    3
    G09744336
    		 Green Front Fog C-CAN BCM 1. CAN line failure
    4
    G09744337
    		 Blue High Beam C-CAN BCM 1. CAN line failure
    5
    G09744338
    		 Green Low Beam Hardwire BCM 1. Wiring failure
    6
    G09744339
    		 Green Hardwire C-CAN BCM 1. Wiring failure
    7
    G09744340
    		 Green Cruise C-CAN EMS 1. CAN line failure
    8
    G09744341
    		 Green SET C-CAN EMS 1. CAN line failure
    9
    G09744342
    		 Red Seat Belt C-CAN BCM 1. CAN line failure
    10
    G09744343
    		 Red Air Bag C-CAN ACU 1. CAN line failure
    11
    G09744344
    		 Yellow Trunk Open C-CAN BCM 1. CAN line failure
    12
    G09744345
    		 Red Door Open C-CAN BCM 1. CAN line failure
    13
    G09744346
    		 Red High Temperature C-CAN EMS 1. CAN line failure
    14
    G09744347
    		 Yellow Immobilizer Hardwire SMK 1. Wiring failure
    15
    G09744348
    		 Yellow ABS C-CAN ESC 1. CAN line failure
    16
    G09744349
    		 Yellow ESC C-CAN ESC 1. CAN line failure
    17
    G09744350
    		 Yellow ESC OFF C-CAN ESC 1. CAN line failure
    18
    G09744351
    		 Yellow TPMS (Tread & Fail) C-CAN TPMS 1. CAN line failure
    19
    G09744352
    		 Yellow Fuel Low Low fuel resistance Fuel Sender
    1. Fuel sender failure
    2. Wiring failure
    20
    G09744353
    		 Red Parking Brake C-CAN BCM & ABS
    or
    ESC    		 1. CAN line failure
    21
    G09744354
    		 Yellow Oil Pressure Hardwire Oil Pressure Sensor 1. Wiring failure
    22
    G09744355
    		 Red Battery Charge Hardwire Battery Sensor 1. Wiring failure
    23
    G09744356
    		 Yellow Check Engine C-CAN EMS 1. CAN line failure
    24
    G09744357
    		 Yellow Low Washer Hardwire Water Level Sensor 1. Wiring failure
    25
    G09744358
    		 Green Active ECO Hardwire ECO ON/OFF Switch
    1. Switch failure
    2. Wiring failure
    Passive ECO C-CAN
    26
    G09744359
    		 Red EPS C-CAN EPS Unit
    1. EPS unit failure
    2. CAN line failure
  2. Check point (Gauge)
    No. Name Signal Input Signal Control (Unit/Sensor) Check Point
    1 Speedometer C-CAN TCS, ABS 1. CAN Line failure
    2 Tachometer C-CAN EMS 1. CAN Line failure
    3 Cooling water temperature C-CAN EMS 1. CAN Line failure
    4 Fuel Hardwire Fuel sender
    1. Fuel sender failure
    2. Wiring failure
  3. Connector terminal check list
    No. Description Input/Output Communication Check Point
    Spec Condition
    A1 Alternator L output Output Hardwire - IGN switch ON
    A2 DC 12V input Input Hardwire - IGN switch ON
    A3 Air Bag (+) Input Hardwire 9 ~ 16 V IGN switch ON
    A4 Rheostat up switch Input Hardwire Below 2V IGN switch ON
    Rheostat up switch ON
    A5 Rheostat down switch Input Hardwire Below 2V IGN switch ON
    Rheostat down switch ON
    A6 Oil pressure indicator Input Hardwire Below 1.5V IGN switch ON
    Oil pressure switch ON
    A7 Active ECO Input Hardwire Below 1.5V IGN switch ON
    A8 Battery Charge Input Hardwire Below 1.5V IGN switch ON
    Charge switch ON
    A9 Low washer Input Hardwire - IGN switch ON
    A10 Immobilizer indicator Input Hardwire/CAN Below 1.5V IGN switch ON
    A11 Steering wheel input Hardwire - IGN switch ON
    A12 Trip switch 1 Input Hardwire 0.7 ~ 4.4 V IGN switch ON
    A13 Trip switch (-) Ground Hardwire Below 1V Switch ground input
    A14 AT S output Output Hardwire 7 ~ 15 V IGN switch ON
    A15 AT R position output Output Hardwire 7 ~ 15 V IGN switch ON
    A16 AT D position output Output Hardwire 7 ~ 15 V IGN switch ON
    A17 AT N position output Output Hardwire 7 ~ 15 V IGN switch ON
    A18 AT P position output Output Hardwire 7 ~ 15 V IGN switch ON
    A19 Detent output Output Hardwire 9 ~ 16 V IGN switch ON
    Rheostat MAX
    A20 4P output Output Hardwire 9 ~ 16 V IGN switch ON
    Vehicle speed 1km/h excess
    A21 Battery (+) Input Hardwire 9 ~ 16 V Always
    A22 Ignition (+) Input Hardwire 9 ~ 16 V IGN switch ON
    A23 Illumination (+) Input Hardwire Above 6 V IGN switch ON
    Illumination (+) switch ON
    A24 -        
    A25 Signal ground 1 Ground Hardwire Below 1V Switch ground input
    A26 -        
    A27 MM CAN High Input/Output CAN - -
    A28 MM CAN Low Input/Output CAN - -
    A29 -        
    A30 C CAN High Input/Output CAN - -
    A31 C CAN Low Input/Output CAN - -
    A32 -        
    A33 Signal ground 2 Ground Hardwire Below 1V Switch ground input
    A34 Fuel (-) Ground Hardwire Below 1V Always
    A35 Fuel (+) Input Hardwire Below 1.1 V IGN switch ON
    Fuel Full
    Above 10.7V IGN switch ON
    Fuel Empty
    A36 5V output Output - - -
    A37 Trip switch 2 Input Hardwire 0.7 ~ 4.4 V IGN switch ON
    A38 Speed Input CAN 9 ~ 16 V IGN switch ON
    A39 Ice warning Input - - -
    A40 Illumination output Output Hardwire 9 ~ 16 V IGN switch ON
    Illumination (+) switch ON
  4. Communication information
    Transmission Unit Receive Unit CAN communication Reference
    Cluster BCM C-CAN Refuel detected state
    Instant fuel consumption information
    Low fuel warning information
    Vehicle setting condition
    Illumination setting
    Cluster EMS C-CAN
    MM-CAN    		 SPORT/ECO Mode
    TCU
    ECS
    ESP
    AVN
    Cluster ACU C-CAN Airbag state
    ACU Cluster CAN Airbag warning indicator control
    BCM Cluster CAN Hood indicator display
    DATC Cluster CAN External temperature display
    ECS Cluster CAN Warning control
    EMS Cluster CAN Tachometer control
    Temperature gauge control
    Check engine symbol, CRUISE and SET indicator control
    ESC Cluster CAN -
    BCM Cluster CAN Vehicle setting control
    Warning indicator and warning sound, PAS control
    SMK Cluster CAN Smart key indicator display
    TCS Cluster CAN ESC OFF switch condition display
    Warning indicator display
    TCU Cluster CAN AT gear information display
    Speed input
    TPMS Cluster CAN TPMS indicator
  5. The other information about the cluster
    1. USM (User Setting Mode)
      • USM is set using the steering wheel remote control button.
      • IMS seat, IMS steering, auto door lock/unlock, head lamp escort, welcome light, welcome sound and triple turn signal lamp are controlled.
    2. USM setting procedure
      1. Send the USM value to the BCM
      2. BCM send the setting value to the each module through CAN.
      3. Each modules send the setting complete value to BCM.
      4. BCM send the final setting value to cluster through CAN.
scientia non olet · About LEMON Manuals