Diagnostic Test

WARNING: This page is about a different car, the 2024 Jeep Grand Wagoneer L and 2024 Jeep Grand Wagoneer. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR OTHER DTCS
1. Refer to the recorded DTCs.
  Are there any Fuel Injector related DTCs present?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to DIAGNOSTIC CODE INDEX .
  No
  - Go To 2
READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 10.0 seconds.
5. Turn the ignition on.
6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE BANK 1 HIGH PRESSURE FUEL INJECTOR CONNECTORS AND TERMINALS
1. Turn the ignition off.
2. Check the Bank 1 High Pressure Fuel Injector harness connectors for proper connection at the Throttle Body.
3. Verify that the connector is completely plugged in and properly locked prior to disconnecting.
4. Disconnect the Bank 1 High Pressure Fuel Injector harness connectors and check for any pushed out, damaged or spread terminals.
  Were any issues found with the connectors or terminals?
  
  Yes
  - Repair the damaged terminal or properly connect and lock the Bank 1 High Pressure Fuel Injector harness connectors and retest for DTCs.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
REPLACE THE BANK 1 HIGH PRESSURE FUEL INJECTORS AND RETEST FOR DTCS
1. Turn the ignition off.
2. Replace the Bank 1 High Pressure Fuel Injectors in accordance with the Service Information.
3. Connect all disconnected harness connectors.
4. Turn the ignition on.
5. With the scan tool, erase all DTCs.
6. Turn the ignition off for a minimum of 10.0 seconds.
7. Turn the ignition on.
8. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
9. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 5
  No
  - Replacing the Bank 1 High Pressure Fuel Injectors repaired the fault.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .