Special Tools
WARNING: This page is about a different car, the 2024 Jeep Grand Cherokee L. However, it is still accessible from the selected car via links, so may be relevant.
| 1130 - Splitter, Bearing/Gear (Originally Shipped In Kit Number(s) 6745, 6947, 6949, 9202, 9202A-CAN, 9202CC, 9299.) |
|
| 6787A - Remover, Bearing Cup (Originally Shipped In Kit Number(s) 6784, 6809.) |
|
| 6936 - Spacer (Originally Shipped In Kit Number(s) 6945, 6946, 6947, 6948.) |
|
| 8285 - Compressor, Spring (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) |
|
| 8481 - Installer, Gear (Originally Shipped In Kit Number(s) 8708, 8708CC.) |
|
| 8901A - Pressing Tool (Originally Shipped In Kit Number(s) 8901A.) |
|
| 8925-3 - Assembly, Press Fixture (Originally Shipped In Kit Number(s) 8998, 8998CC.) |
|
| 9585 - Remover, Bearing Cup (Originally Shipped In Kit Number(s) 9691.) |
|
| 9664 - Remover, Bearing Cup (Originally Shipped In Kit Number(s) 9675, 9685, 9695.) |
|
| 9667 - Remover, Seal (Originally Shipped In Kit Number(s) 9691.) |
|
| 9677 - Installer, Seal (Originally Shipped In Kit Number(s) 9675, 9685, 9695.) |
|
| 10373A - Installer, Output Needle Bearing/Rear Oil Dam (Originally Shipped In Kit Number(s) 10394A.) |
|
| 10375 - Installer, Oil Pump Cover Oil Seal (Originally Shipped In Kit Number(s).) |
|
| 10376 - Installer, Input Shaft Needle Bearing (Originally Shipped In Kit Number(s) 10394A, 10394-UPD.) |
|
| 10377 - Remover/Installer, Guide Sleeve (Originally Shipped In Kit Number(s).) |
|
| 10378 - Rings, Support (Originally Shipped In Kit Number(s).) |
|
| 10379 - Pins, Valve Body Alignment (Originally Shipped In Kit Number(s).) |
|
| 10382 - Installer, Oil Pump Housing Needle Bearing (Originally Shipped In Kit Number(s) 10394A, 10394-UPD.) |
|
| 10383 - Plate, Clutch Pressure Test (Originally Shipped In Kit Number(s).) |
|
| 10428 - Adapter, Pressing Tool (Originally Shipped In Kit Number(s).) |
|
| 10429 - Gauge, Force (Originally Shipped In Kit Number(s) 10419.) |
|
| C-637 - Slide Hammer, Universal (Originally Shipped In Kit Number(s) 9202.) |
|
| C-3281 - Holder, Flange (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202CC, 9299, 9299CC, 9299CC, 9300A-CAN.) |
|
| C-3752 - Slide Hammers (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202-CAN, 9202CC.) |
|
| C-4171 - Driver Handle, Universal (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202CC, 9299, 9299CC, 9299CC, 9300A-CAN.) |
|
| C-4171-4 - Extension, Drive Handle (Originally Shipped In Kit Number(s).) |
|
| 2055000090 - Installer, Oil Seal (Originally Shipped In Kit Number(s).) |