LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2023 >> Wagoneer Carbide, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 24 (5.7L - DTCS P2271 To P3441) >> DTC Troubleshooting >> P24D7-EVAP System Pressure Sensor 2 Circuit Low >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. CHECK FOR ANY SERVICE BULLETINS OR PCM SOFTWARE UPDATES 
    1. Check for any applicable Service Bulletins or Flash updates related to the DTC.

      Are there any applicable Service Bulletins or Flash updates?

      Yes 

      No 

      • Go To  2
  2. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
    2. For future reference, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 10.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  3

      No 

  3. CHECK FOR OTHER DTCS 
    1. Refer to the recorded DTCs.

      Are there any 5-Volt Supply DTCs present?

      Yes 

      No 

      • Go To  4
  4. CHECK THE FTP SENSOR CONNECTOR AND TERMINALS 
    1. Turn the ignition off.
    2. Check the FTP Sensor harness connector for proper connection at the FTP Sensor.
    3. Verify that the connector is completely plugged in and properly locked prior to disconnecting.
    4. Disconnect the FTP Sensor harness connector and check for any pushed out, damaged or spread terminals.

      Were any issues found with the connector or terminals?

      Yes 

      • Repair the damaged terminal or properly connect and lock the FTP Sensor harness connector and retest for DTCs.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  5
  5. CHECK THE (N8) 5-VOLT SUPPLY CIRCUIT VOLTAGE 
    1. Turn the ignition off.
    2. Disconnect the FTP Sensor harness connector.
    3. Turn the ignition on.
    4. Measure the voltage on the (N8) 5-Volt Supply circuit at the FTP Sensor harness connector.

      Is the voltage between 4.8 and 5.6 volts?

      Yes 

      • Go To  6

      No 

      • Repair the (N8) 5-Volt Supply circuit for an open/high resistance or short to ground.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  6. CHECK THE (N16) FTP SENSOR 2 SIGNAL CIRCUIT FOR A SHORT TO GROUND 
    1. Turn the ignition off.
    2. Disconnect the FTP Sensor 2 harness connector.
    3. Disconnect the PCM C1 harness connector.
    4. Check for continuity between ground and the (N16) FTP Sensor 2 Signal circuit at the FTP Sensor harness connector.

      Is there continuity between ground and the (N16) FTP Sensor 2 Signal circuit?

      Yes 

      • Repair the (N16) FTP Sensor 2 Signal circuit for a short to ground.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  7
  7. CHECK FOR A SHORT BETWEEN THE (N16) FTP SENSOR 2 SIGNAL CIRCUIT AND THE (N10) SENSOR GROUND CIRCUIT 
    1. Check for continuity between the (N16) FTP Sensor 2 Signal circuit and the (N10) Sensor Ground circuit at the FTP Sensor harness connector.

      Is there continuity between the (N16) FTP Sensor 2 Signal circuit and the (N10) Sensor Ground circuit?

      Yes 

      • Repair the short between the (N16) FTP Sensor 2 Signal circuit and the (N10) Sensor Ground circuit.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  8
  8. CHECK THE ABILITY OF THE PCM TO READ THE FUEL TANK PRESSURE SENSOR 2 SIGNAL 
    1. Connect the PCM C1 harness connector.
    2. Connect a jumper between the (N16) FTP Sensor 2 Signal circuit and the (N8) 5-Volt Supply circuit at the FTP Sensor 2 harness connector.
    3. Turn the ignition on.
    4. With the scan tool, read DTCs.

      Does the DTC P24D8-EVAP SYSTEM PRESSURE SENSOR 2 CIRCUIT HIGH set?

      Yes 

      No 

      • Go To  9
  9. CHECK RELATED PCM AND COMPONENT CONNECTIONS 
    1. Disconnect all PCM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    10. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

      • The wiring or poor connection problem has been repaired.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
scientia non olet · About LEMON Manuals