LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2022 >> Gladiator Mojave, Part Time T/Case Control, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 28 (3.0L Diesel - DTCS P20B9-00 To P2195-00) >> DTC Troubleshooting >> P2128-00-Accelerator Pedal Position Sensor 2 Circuit High >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
    2. For future reference, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 75.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

      • Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT DTC .
  2. CHECK FOR OTHER DTCS 
    1. Refer to the recorded DTCs.

      Are there any Sensor Reference or Sensor Supply voltage DTCs present?

      Yes 

      No 

      • Go To  3
  3. CHECK THE APP SENSOR 2 (K29) SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Disconnect the PCM C1 harness connector.
    2. Remove the ASD Relay from the Power Distribution Center (PDC).
    3. Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay connector.
    4. Turn the ignition on.
    5. Measure the voltage of the APP Sensor 2 (K29) Signal circuit in the APP Sensor harness connector.

      Is there voltage present on any of the circuits?

      Yes 

      No 

      • Go To  4
  4. CHECK THE APP SENSOR 2 (K29) SIGNAL CIRCUIT FOR A SHORT TO THE 5-VOLT SUPPLY CIRCUITS 
    1. Turn the ignition off.
    2. Remove the jumper wire and install the ASD Relay.
    3. Measure the resistance between the APP Sensor 2 (K29) Signal circuit and the (K856) 5-Volt Supply circuit at the APP Sensor harness connector.
    4. Measure the resistance between the APP Sensor 2 (K29) Signal circuit and the (K855) 5-Volt Supply circuit at the APP Sensor harness connector.

      Is the resistance above 10k Ohms between the APP Sensor 2 (K29) Signal circuit and 5-Volt Supply circuits?

      Yes 

      • Go To  5

      No 

      • Repair the APP Sensor 2 (K29) Signal circuit for a short to the circuit that measured below 10k Ohms.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  5. CHECK THE APP SENSOR 2 (K29) SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Measure the resistance of the APP Sensor 2 (K29) Signal circuit between the APP Sensor harness connector and the PCM C1 harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  6

      No 

  6. ACCELERATOR PEDAL POSITION SENSOR 
    1. Reconnect the APP Sensor harness connector.
    2. Reconnect the PCM C1 harness connector.
    3. Turn the ignition on.
    4. With the scan tool, erase DTCs.
    5. Turn the ignition off.
    6. Disconnect the APP Sensor harness connector.
    7. Connect a jumper wire between the (K400) Sensor Ground circuit and the APP Sensor 2 (K29) Signal circuit at the APP Sensor harness connector.
    8. Turn the ignition on.
    9. With the scan tool, select View DTCs.
      NOTE:

      The scan tool should display an Accelerator Pedal Position Sensor 2 Low DTC as active with the jumper wire in place.

      Does the scan tool display the DTC as described above?

      Yes 

      • Replace the Accelerator Pedal Position Sensor in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  7
  7. CHECK RELATED PCM AND COMPONENT CONNECTIONS 
    1. Perform any Service Bulletins that apply.
    2. Disconnect all PCM harness connectors.
    3. Disconnect all related in-line harness connections (if equipped).
    4. Disconnect the related component harness connectors.
    5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    9. With the scan tool, erase DTCs.
    10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    11. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .

      No 

scientia non olet · About LEMON Manuals