LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2022 >> Gladiator Mojave, Part Time T/Case Control, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 22 (3.0L Diesel - DTCS P0557-00 To P05F8-00) >> DTC Troubleshooting >> P05F3-00-Exhaust AFTERTREATMENT Power Relay Control Circuit Open >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
    2. For future reference, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 75.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

      • Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT DTC .
  2. CHECK THE SCR RELAY 2 FOR PROPER OPERATION 
    1. Turn the ignition off.
    2. Use a known good relay in place of the SCR Relay 2 in the Power Distribution Center (PDC).
    3. Ignition on, engine not running.
    4. With the scan tool, erase DTCs in the Powertrain Control Module (PCM).
    5. Start the engine and allow it to reach normal operating temperature.
    6. With the scan tool, select View DTCs.

      Does the DTC return?

      Yes 

      • Go To  3

      No 

      • Repair is complete. Reset the SCR Timer: Using the scan tool, go to Misc. Functions>SCR Extend Mileage W Active Fault (and reset the Timer).
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  3. CHECK THE SCR RELAY 2 (K402) CONTROL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Turn the ignition off.
    2. Remove the SCR Relay 2.
    3. Disconnect the PCM C1 harness connector.
    4. Measure the resistance of the SCR Relay 2 (K402) Control circuit between the SCR Relay 2 (in the PDC) and the PCM C1 harness connector.

      Is the resistance above 5.0 Ohms?

      Yes 

      • Go To  4

      No 

      • Go To  5
  4. CHECK THE SCR RELAY 2 (K402) CONTROL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Disconnect the PDC C3 harness connector.
    2. Measure the resistance of the SCR Relay 2 (K402) Control circuit between the SCR Relay 2 (in the PDC) and the PDC C3 harness connector.

      Is the resistance above 5.0 Ohms?

      Yes 

      • Replace the Power Distribution Center (PDC) in accordance with the Service Information. Reset the SCR Timer: Using the scan tool, go to Misc. Functions>SCR Extend Mileage W Active Fault (and reset the Timer).
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .

      No 

      • Repair the SCR Relay 2 (K402) Control circuit (between the PDC and the PCM) for an open/high resistance. Reset the SCR Timer: Using the scan tool, go to Misc. Functions>SCR Extend Mileage W Active Fault (and reset the Timer).
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  5. CHECK RELATED HARNESS CONNECTIONS 
    1. Disconnect all PCM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    10. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .

      No 

scientia non olet · About LEMON Manuals