Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, run and save a vehicle Scan Report and all related recorded data.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 10.0 seconds.
5. Turn the ignition on.
6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT DTC .
CHECKING FOR OTHER PCM DTCS
1. With the scan tool, read the PCM DTCs.
  Are there any other DTCs present?
  
  Yes
  - Repair the other DTCs before continuing.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE FUEL SYSTEM FOR A LEAK
1. Turn the ignition off.
2. Inspect the entire fuel system for leakage.
  Is there any evidence of leakage?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE FUEL SYSTEM FOR CONTAMINATION
1. Inspect the fuel system for contamination.
  Is the fuel contaminated?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK THE ENGINE FOR PROPER STARTING CONDITIONS
1. With the scan tool, erase the PCM DTCs.
2. Attempt to start the engine.
  Does the engine start and idle?
  
  Yes
  - Go To 6
  No
  - Go To 9
CHECK THE FUEL PRESSURE REGULATOR FOR PROPER OPERATION
1. With the scan tool, compare the Fuel Pressure Setpoint with the Actual Fuel Pressure.
  NOTE:
  A sticking Fuel Pressure Regulator is indicated by the Actual Fuel Pressure gradually dropping below the Fuel Pressure Set point then suddenly increasing (spiking) above the Fuel Pressure Set point.
  
  Does the Actual Fuel Pressure gradually decrease then suddenly increase (spike) above the Fuel Pressure Setpoint?
  
  Yes
  - Replace the Fuel Pressure Regulator in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Go To 7
CHECK THE FUEL DELIVERY SYSTEM FOR PROPER OPERATION
1. Perform the CHECKING THE FUEL DELIVERY SYSTEM diagnostic procedure. Refer to CHECKING THE FUEL DELIVERY SYSTEM .
  Were there any problems with the Fuel Delivery System?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Go To 8
CHECK THE FUEL INJECTOR(S) FOR PROPER OPERATION
NOTE:
An injector that sticks open can cause this DTC. A sticking injector will cause the engine to misfire and emit excessive black smoke from the exhaust system.

Does the engine exhibit the symptoms described in the above note?

Yes
- Using the service information, remove and inspect the Fuel Injectors for signs of damage or debris that may cause the injector to stick. Sticking injectors may cause the combustion chamber to become black and oil soaked. Replace Injector(s) as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
No
- Go To 9
CHECK THE FUEL DELIVERY SYSTEM FOR PROPER OPERATION
1. Perform the CHECKING THE FUEL DELIVERY SYSTEM diagnostic procedure. Refer to CHECKING THE FUEL DELIVERY SYSTEM .
  Were there any problems with the Fuel Delivery System?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Go To 10
CHECK THE FUEL QUANTITY SOLENOID FOR PROPER OPERATION
1. Turn the ignition off.
2. Turn the ignition on.
3. With the scan tool, erase the PCM DTCs.
4. Attempt to start and test drive the vehicle.
5. With the scan tool, read the PCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Fuel Quantity Solenoid in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - Test Complete.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .