Torque Specifications
WARNING: This page is about a different car, the 2019 RAM 3500 HD and 2019 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.
CYLINDER HEAD
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Camshaft Phaser Bolt | 98 | 72 | - | |
| Camshaft Thrust Plate Bolts | 13 | 10 | - | |
| Cylinder Head Bolts | Specific Torque Sequence Refer to CYLINDER HEAD, REMOVAL AND INSTALLATION . | |||
| Cylinder Head Cover Bolts | 11 | 8 | - | |
| Exhaust Manifold - Medium Duty | Specific torque and fastener pattern required; follow installation sequence. Refer to MANIFOLD, EXHAUST, REMOVAL AND INSTALLATION . | |||
| Exhaust Manifold - Heavy Duty | Specific torque and fastener pattern required; follow installation sequence. Refer to MANIFOLD, EXHAUST, REMOVAL AND INSTALLATION . | |||
| Exhaust Manifold Heat Shield Nuts | 10 | - | 89 | |
| Exhaust Manifold to Exhaust Pipe/Catalytic Convertor | 32 | 24 | - | |
| Forward Nuts | 8 | - | 71 | |
| Rearward Nuts | 14 | 10 | - | |
| Intake Manifold Bolts | Specific Torque Sequence Refer to MANIFOLD, INTAKE, REMOVAL AND INSTALLATION . | |||
| Rocker Arm Bolts | Specific Torque Sequence Refer to ROCKER ARM, VALVE, REMOVAL AND INSTALLATION . | |||
ENGINE BLOCK
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Connecting Rod Cap Bolts | 40 + 90° Turn | 30 + 90° Turn | - | |
| Engine Block Pipe Plugs | ||||
| Oil Galley Plug (1/4 - 18 NPT) | 20 | 15 | - | |
| Coolant Drain Plug (1/4 - 18 NPT) | 34 | 25 | - | |
| (3/8 NPT) | 27 | 20 | - | |
| Lifter Guide Holder | 12 | 9 | - | |
| Main Bearing Cap Bolts | Specific Torque Sequence Refer to REMOVAL AND INSTALLATION . | |||
| Multiple Displacement Solenoid (MDS) | 11 | 8 | - | |
| Oil Level Indicator Tube to Exhaust Manifold Nut | 10 | - | 89 | |
| Oil Level Indicator Tube to Engine Block Bolt | 12 | 9 | - | |
| Oil Pan Bolts/Studs | 12 | 9 | - | |
| Oil Pan Drain Plug | 34 | 25 | - | |
| Oil Pump Bolts | 32 | 24 | - | |
| Oil Pump Pickup Tube Bolt | 22 | 16 | - | |
| Oil Pump Pickup Tube Nut | 28 | 21 | - | |
| Rear Seal Retainer Bolts | 13 | 10 | - | |
| Structural Dust Cover Bolts | Specific Torque Sequence Refer to COVER, STRUCTURAL DUST, REMOVAL AND INSTALLATION . | |||
| Timing Chain Cover Bolts | 28 | 21 | - | |
| Timing Chain Cover Slide Bushing Bolt | 25 | 18 | - | |
| Timing Drive Guide Bolts | 11 | 8 | - | |
| Timing Drive Tensioner Bolts | 11 | 8 | - | |
| Vibration Damper Bolt | 185 | 136 | - | |
| Variable Valve Timing Solenoid (VVTS) | 11 | 8 | - | |
FRONT ENGINE
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Belt Tensioner Bolt | 55 | 41 | - | |
| Engine Coolant Temperature Sensor | 27 | 20 | - | |
| Engine Oil Pressure Sensor | 14 | 10 | - | |
| Engine Oil Temperature Sensor | 27 | 20 | - | |
| Idler Pulley Bolt | 25 | 18 | - | |
| Oil Cooler Adapter Bolt to Engine Block | 12 | 9 | - | |
| Thermostat Housing Bolts | 28 | 21 | - | |
| Water Pump Bolts | 28 | 21 | - |
REAR ENGINE
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Flexplate to Crankshaft Bolts | 95 | 70 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
ENGINE MOUNTS
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Front Engine Mount to Frame Through Bolts/Nuts (2WD/4WD) | 130 | 96 | - | |
| Engine Mount to Block Bolts (2WD/4WD) | 62 | 46 | - | Apply Thread Lock to Bolts |
| Rear Mount Isolator to Transmission Mount Bracket Nuts (2WD/4WD) | 110 | 81 | - | Apply Thread Lock |
| Rear Mount Isolator to Transmission Crossmember Nuts (2WD/4WD) | 61 | 45 | - | Apply Thread Lock |
| Transmission Adaptation Bracket to Transmission (4WD) | 61 | 45 | - | Apply Thread Lock to Bolts |
| Transmission Mount Bracket to Transmission Bolts (2WD) | 61 | 45 | - | Apply Thread Lock to Bolts |
MISCELLANEOUS COMPONENTS
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Air Cleaner Housing Cover Bolts | 5 | - | 44 | |
| Air Cleaner Inlet to Fan Shroud | 4 | - | 35 | |
| Air Cleaner Inlet Hose Clamps | 4 | - | 35 |