Diagnostic Test

WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR TCM DTC U0001-00
1. With the scan tool, read DTCs and record on the repair order.
  Is U0001-00 set in the TCM?
  
  Yes
  - Perform the DTC U0001-00 CAN C BUS procedure. Refer to DIAGNOSTIC CODE INDEX .
  No
  - Go To 2
CHECK FOR OTHER TCM CAN BUS DTCS
1. Refer to the recorded DTCs.
  Are any other TCM CAN bus DTCs set?
  
  Yes
  - Perform the applicable TCM CAN bus DTC procedure(s). Refer to DIAGNOSTIC CODE INDEX . first if the fault is present.
  No
  - Go To 3
CHECK FOR PCM DTCS
1. Refer to the recorded DTCs.
  Are any PCM DTCs set?
  
  Yes
  - Perform the applicable PCM DTC procedure(s). Refer to DIAGNOSTIC CODE INDEX, 1.3L or DIAGNOSTIC CODE INDEX, 2.4L .
  No
  - Go To 4
CHECK FOR AN ACTIVE DTC
1. With the scan tool, read TCM DTCs.
2. Record the Event Data and Environmental Data.
3. With the scan tool, erase DTCs.
4. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read TCM DTCs.
  Did this DTC return?
  
  Yes
  - Go To 5
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all TCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all TCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read TCM DTCs.
  Did the DTC return?
  
  Yes
  - If this Electronic Control Unit (ECU) is being replaced with a new unit, a diagnostic scan tool MUST be used to align the PROXI configuration data into the new ECU. Follow the routine outlined in the diagnostic scan tool for PROXI Configuration Alignment under Body Control Module (BCM) Miscellaneous Functions menu.
  - Replace the Transmission Control Module (TCM) and perform the PROXI Configuration Alignment procedures in accordance with the Service information. Refer to MODULE, TRANSMISSION CONTROL (TCM), REMOVAL AND INSTALLATION .
  - Perform the TRANSMISSION VERIFICATION TEST. Refer to TRANSMISSION VERIFICATION TEST - 948TE 9HP48 .
  No
  - Repair the circuits or poor connections.
  - Perform the TRANSMISSION VERIFICATION TEST. Refer to TRANSMISSION VERIFICATION TEST - 948TE 9HP48 .