Diagnostic Test

WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DTC
1. Verify the Park Assist Sensor is connected before proceeding with this diagnostic procedure.
  NOTE:
  A disconnected sensor will set this DTC.
2. With the scan tool, read DTCs and record on the repair order.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
REAR INNER RIGHT SENSOR SIGNAL CIRCUIT SHORTED TO BATTERY
1. Turn the ignition off.
2. Disconnect the Park Assist Module (PAM) harness connector.
3. Disconnect the Park Assist Sensor harness connector.
4. Turn the ignition on.
5. Measure the voltage between ground and the Rear Inner Right Sensor Signal circuit at the Park Assist Sensor harness connector.
  Is the voltage above 10.0 volts?
  
  Yes
  - Repair the Rear Inner Right Sensor Signal circuit for a short to battery.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
REAR INNER RIGHT SENSOR SIGNAL CIRCUIT SHORTED TO THE REAR INNER RIGHT SENSOR SUPPLY CIRCUIT
1. Turn the ignition off.
2. Check for continuity between the Rear Inner Right Sensor Signal circuit and the Rear Inner Right Sensor Supply circuit at the Park Assist Module harness connector.
  Is there continuity between the Rear Inner Right Sensor Signal circuit and the Rear Inner Right Sensor Supply circuit?
  
  Yes
  - Repair the Rear Inner Right Sensor Signal circuit for a short to the Rear Inner Right Sensor Supply circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 4
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all PAM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all PAM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Park Assist Module (PAM) in accordance with the Service Information. Refer to MODULE, PARK ASSIST, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - The wiring or poor connection has been repaired.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .