LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2019 >> Renegade High Altitude, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1379 (1.3L - DTCS P0107 To P025C) >> DTC Troubleshooting >> P0113-Intake Air Temperature Sensor 1 Circuit High >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR ANY SERVICE BULLETINS OR PCM SOFTWARE UPDATES 
    1. Check for any applicable Service Bulletins or Flash updates related to the DTC.

      Are there any applicable Service Bulletins or Flash updates?

      Yes 

      No 

      • Go To  2
  2. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
    2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 10.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  3

      No 

  3. CHECK THE (K222) IAT SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Turn the ignition off.
    2. Disconnect the IAT Sensor harness connector
    3. Turn the ignition on.
    4. Measure the voltage on the (K222) IAT Signal circuit at the IAT Sensor harness connector.

      Is the voltage above 5.2 volts?

      Yes 

      • Repair the (K222) IAT Signal circuit for a short to voltage.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  4
  4. CHECK THE (K222) IAT SIGNAL FOR AN OPEN/HIGH RESISTANCE 
    1. Turn the ignition off.
    2. Disconnect the PCM C1 harness connector.
      CAUTION:

      Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.

    3. Connect the

      (special tool #10436, Adapter, GPEC Diagnostic)

      to the appropriate PCM connector.

      NOTE:

      The GPEC Diagnostic Adaptor can add up to 1.5 Ohms of resistance to the circuit.

    4. Measure the resistance of the (K222) IAT Signal circuit between the IAT Sensor harness connector and the GPEC Diagnostic Adaptor.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  5

      No 

      • Repair the (K222) IAT Signal circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  5. CHECK THE (K914) SENSOR GROUND CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Measure the resistance of the (K914) Sensor Ground circuit between the IAT Sensor harness connector and the GPEC Diagnostic Adaptor.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  6

      No 

      • Repair the (K914) Sensor Ground circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  6. CHECK THE ABILITY OF THE PCM TO READ THE INTAKE AIR TEMPERATURE SENSOR SIGNAL 
    1. Reconnect the PCM C1 harness connector.
    2. Connect a jumper between the (K222) IAT Signal circuit and the (K914) Sensor Ground at the IAT Sensor harness connector.
    3. Turn the ignition on.
    4. With the scan tool, read DTCS.
      NOTE:

      The DTC P0112-00-INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT LOW should be active or pending with the jumper in place.

      Does the scan tool display as described above?

      Yes 

      No 

      • Go To  7
  7. CHECK RELATED PCM AND COMPONENT CONNECTIONS 
    1. Perform any Service Bulletins that apply.
    2. Disconnect all PCM harness connectors.
    3. Disconnect all related in-line harness connections (if equipped).
    4. Disconnect the related component harness connectors.
    5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    9. With the scan tool, erase DTCs.
    10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    11. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

      • The wiring or poor connection problem has been repaired.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
scientia non olet · About LEMON Manuals