Diagnostic Test

WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read DTCs and record on the repair order.
2. Record the Environmental Data.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read HVAC Module DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (F710) 5 VOLT REFERENCE SIGNAL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT AT THE ELECTRONIC CONTROL UNIT (ECU) HARNESS CONNECTOR
1. The ignition must be off when performing a resistance check to find a short between circuit s.
2. Isolate the circuit by disconnecting the ECU and the component harness connectors containing the circuit being tested.Note: Use the wiring diagram as a guide to follow the path of the circuit. Check the disconnected connectors and related harnesses for damage, corrosion, and loose fitting terminals.
3. Connect one lead of the Digital Volt-Ohm Meter (DVOM) to the circuit being tested at the ECU harness connector.
4. With the other lead of the DVOM probe all other circuits at the ECU harness connector.
  NOTE:
  When back-probing a circuit at a harness connector, always use an appropriate back probing tool to prevent damage to the connector terminals.
  
  Is there continuity between the circuit being tested and any other circuit?
  
  Yes
  - Repair the circuit for a short to another circuit. Use the wiring diagram as a guide to trace the circuits and look for any in-line connectors to help isolate the location of the short.
  - Perform the HVAC VERIFICATION TEST. Refer to HVAC VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (F710) 5 VOLT REFERENCE SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition on.
2. Measure voltage on the (F710) 5 Volt Reference Signal circuit at the ECU harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the circuit for a short to voltage. Use the wiring diagram as a guide to trace the circuits and look for any in-line connectors to help isolate the location of the short.
  - Perform the HVAC VERIFICATION TEST. Refer to HVAC VERIFICATION TEST .
  No
  - Go To 4
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all HVAC Module harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all HVAC Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read HVAC Module DTCs.
  Did the DTC return?
  
  Yes
  - Replace the HVAC Module in accordance with the Service information. Refer to MODULE, HVAC, REMOVAL AND INSTALLATION .
  - Perform the HVAC VERIFICATION TEST. Refer to HVAC VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform the HVAC VERIFICATION TEST. Refer to HVAC VERIFICATION TEST .