Diagnostic Test

WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DTC
1. Turn the ignition on.
2. With the scan tool, read DTCs and record on the repair order.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT DTC diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK FOR OTHER DTCS
1. Refer to the recorded DTCs.
  Are there any CAN C, Communication, or System Voltage DTCs active or pending?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to DIAGNOSTIC CODE INDEX .
  No
  - Go To 3
CHECK THE ABILITY OF THE BCM TO READ THE AMBIENT AIR TEMPERATURE SENSOR SIGNAL
1. Turn the ignition off.
2. Disconnect the AAT harness connector.
3. Turn the ignition on.
4. With the scan tool, read DTCs.
  NOTE:
  The scan tool should display the P0073-AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH DTC as active or pending with the connector unplugged.
  
  Does the scan tool read as described above?
  
  Yes
  - Replace the Ambient Air Temperature Sensor in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE (G31) AAT SIGNAL CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the BCM C6 harness connector.
3. Check for continuity between ground and the (G31) AAT Signal circuit at the Ambient Air Temperature Sensor harness connector.
  Is there continuity between ground and the (G31) AAT Signal circuit?
  
  Yes
  - Repair the (G31) AAT Signal circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK FOR THE (G31) AAT SIGNAL CIRCUIT SHORTED TO THE (G931) AAT SENSOR GROUND CIRCUIT
1. Check for continuity between the (G31) AAT Signal circuit and the (G931) AAT Sensor Ground circuit at the Ambient Air Temperature Sensor harness connector.
  Is there continuity between the (G31) AAT Signal circuit and the (G931) AAT Sensor Ground circuit?
  
  Yes
  - Repair the (G31) AAT Signal circuit for a short to the (G931) AAT Sensor Ground circuit.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 6
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Repair the poor connections.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .