Torque Specifications
WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.
ENGINE BLOCK
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Balance Shaft/Oil Pump Assembly Bolts | Refer to PUMP, ENGINE OIL, REMOVAL AND INSTALLATION . | |||
| Balance Shaft/Oil Pump Assembly Splash Shield Screws | 9 | - | 80 | |
| Connecting Rod Cap Bolts | 20 + 92° | 15 + 92° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Crankshaft Main Bearing Cap Bolts | Refer to BEARING(S), CRANKSHAFT, MAIN, STANDARD PROCEDURE . | |||
| Crankshaft Target Ring Screws | 12 | 9 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Ladder Frame To Cylinder Block Bolts | Refer to FRAME, LADDER, REMOVAL AND INSTALLATION . | |||
| Oil Cooler Connector Union | 40 | 30 | - | |
| Oil Cooler Heatshield Bolts | 8 | - | 71 | |
| Oil Filter | Refer to FILTER, ENGINE OIL, REMOVAL AND INSTALLATION . | |||
| Piston Oil Cooler Jet Bolts | 10 | - | 89 | |
| Dipstick Tube To Cylinder Block Bolt | 25 | 18 | - | |
| Oil Pan To Cylinder Block | ||||
| M6 Bolts | 10 | - | 89 | |
| M8 Bolts | 23 | 17 | - | |
| Oil Pan Drain Plug | 27 | 20 | - | |
| Oil Pressure Relief Valve | 44 | 32 | - | |
| Oil Pressure Sensor | 44 | 32 | - | |
CYLINDER HEAD
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Camshaft Bearing Cap Bolts | 10 | - | 89 | |
| Cylinder Head Bolts | 35 + 160° | 26 + 160° | - | |
| Cylinder Head Cover Bolts | 10 | - | 89 | |
| Multiair Fill Port Plug To Cylinder Head Cover | 21 | 15 | - | |
| Main Oil Gallery M10 Tapered Plug | 5 + 720° | - | 44 + 720° | |
| Engine Cover Ball Stud to Cylinder Head Cover | 3 | - | 27 | |
| Oil Temperature Sensor | 11 | 8 | - | |
| Variable Valve Actuation Assembly (VVAA) To Cylinder Head Bolts | Refer to ASSEMBLY, VARIABLE VALVE ACTUATION, REMOVAL AND INSTALLATION . | |||
FRONT ENGINE
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Balance Shaft/Oil Pump Assembly Chain Splash Shield Bolts | 9 | - | 80 | |
| Balance Shaft/Oil Pump Assembly Fixed Chain Guide Bolts | 12 | 9 | - | |
| Balance Shaft/Oil Pump Assembly Chain Tensioner Arm Bolt | 10 | - | 81 | |
| Balance Shaft/Oil Pump Assembly Chain Tensioner Bolts | 9 | - | 80 | |
| Balance Shaft/Oil Pump Assembly Sprocket Bolt | 25 | 18 | - | |
| Camshaft Sprocket Bolt | 10 + 65° | - | 89 + 65° | |
| Crankshaft Damper Retaining Bolt | 50 + 68° | 37 + 68° | - | |
| Timing Chain Cover | ||||
| M10 Bolts | 65 | 48 | - | |
| M8 Bolts | 25 | 18 | - | |
| M6 Bolts | 9 | - | 80 | |
| Timing Chain Guide Bolts | 12 | 9 | - | |
| Timing Chain Tensioner Arm Bolt | 28 | 21 | - | |
| Timing Chain Tensioner Bolts | 9 | - | 80 | |
REAR ENGINE
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Flexplate To Crankshaft Bolts | 29 + 51° | 21 + 51° | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Battery Negative Cable to Auto Transmission Bolt | 22 | 16 | - | |
| Vacuum Pump Fitting To Vacuum Pump Screw | 8 | - | 71 | |
| Vacuum Pump To Cylinder Head Bolts | 25 | 18 | - |
ENGINE MOUNTING
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Left Engine Mount To Frame Rail Bolts (2) M12 x 60 |
128 | 94 | - | |
| Left Engine Mount To Transmission Bracket Bolts (3) M12 x 63 |
125 | 92 | - | |
| Left Engine Mount Transmission Bracket To Transmission Bolts (4) M12 x 63 |
125 | 92 | - | |
| Left Engine Mount Bracket To Frame Rail Bolt | 24 | 18 | - | |
| Right Engine Mount To Frame Rail Bolts (3) M10 x 44 |
113 | 83 | - | |
| Right Engine Mount To Timing Chain Cover Bolts (3) M10 x 93 |
113 | 83 | - | |
| Rear Engine Mount (Torque Strut) To Cradle Bolt (1) M14 x 82 |
210 | 155 | - | |
| Rear Engine Mount (Torque Strut) To Transmission Bracket Bolt (1) M14 x 82 |
210 | 155 | - | |
| Rear Engine Mount (Torque Strut) Transmission Bracket To Transmission Bolts (3) M14 x 65 |
210 | 155 | - |
MANIFOLDS
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Catalytic Converter Lower Support Bracket Bolts | 20 | 15 | - | |
| Exhaust Manifold to Cylinder Head Bolts | 34 | 25 | - | |
| Exhaust Manifold Heatshield Bolts | 12 | 9 | - | |
| Intake Manifold To Cylinder Head Bolts | 12 | 9 | - | |
| Intake Manifold Silencer Cover Screws | 6 | - | 53 | |
| Intake Manifold Lower Support Bracket Bolt | 24 | 18 | - | |
| Intake Manifold Lower Support Bracket Nuts | 12 | 9 | - |
MISCELLANEOUS COMPONENTS
| DESCRIPTION | Nm | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Air Cleaner Body Lid Screws | 4 | - | 35 | |
| Air Inlet Duct Nut | 8 | - | 71 | |
| Clean Air Hose To Cylinder Head Cover Bolt | 8 | - | 71 | |
| Engine Cover Bolt | 9 | - | 80 | |
| Generator Mounting Bracket Bolts | 50 | 37 | - | |
| Lower Load Beam Reinforcement Bracket Bolts | 10 | - | 81 |