New Vehicle Preparation - North AMERICA

WARNING: This page is about a different car, the 2020 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.

VEHICLE READINESS
NOTE: This document is for reference purposes only. The instructions are not VIN-specific, and it is not required to print or retain this document for each New Vehicle Prep performed.
Description	Action
Remove All Protective Transit Film From Body of Vehicle and Keep All Wheel Covers on Vehicle Until Sold	Remove all protective transit film from the body as soon as the vehicle arrives at the dealership. However, keep all wheel covers on the vehicle until sold
Place vehicle into Customer Mode using wiTECH and micro Pod II (Pro Master, Pro Master City, and Renegade)	Using wiTECH and micro Pod II, take the vehicle out of Logistics Mode by following the Exit Logistics Mode within the Vehicle Prep tab
Inflate tire pressure to the maximum side wall pressure (except Viper)	Increase the tire pressure to the maximum sidewall pressure if vehicle is going into lot storage.
Verify vehicle is built as invoiced	Verify vehicle is built as invoiced
Install all "Shipped Loose" items (except Viper)	Install all "Shipped Loose" items.
Install Front License Plate Bracket (if required)	Install Front License Plate Bracket.
Install Roof Rack	Install Roof Rack.
Install Antenna	Install Antenna.
Perform all Incomplete Recalls and RRTs	Perform all Incomplete Recalls and RRTs
Install Wheel Center Caps	Install Wheel Center Caps.
Open the LPG valve (EMEA Only)	Open the LPG valve. Refer to NEW VEHICLE PREPARATION INSTRUCTIONS, STANDARD PROCEDURE .(EMEA Only)

UNDERHOOD
Description	Action
Hood Latch and Safety Catch - Adjust as Needed	Verify the operation of the hood release system including the inside hood release lever and the outside hood secondary safety catch. Adjust if necessary. The safety catch prevents the hood from going to the full open position until it is manually released. To test the safety catch, unlatch the hood with the interior hood release lever and attempt to raise the hood without operating the safety catch.
Battery State-of-Charge - document voltage	Check the battery state of charge by connecting a digital voltmeter at the jump-start locations. The battery voltage should be at least 12.4 volts (Fiat 500 BEV -100%). If charging is necessary, follow the service information procedures and recharge the battery. Record voltage on New Vehicle Prep (NVP) form.
Battery State-of-Charge - document voltage	For international EMEA market vehicles, print the primary battery and/or the ESS auxiliary battery (If equipped) status check result ticket and archive it together with the New Vehicle Prep Check Sheet. Refer to Service Bulletin 08-073-17. NOTE: For international EMEA market vehicles the 12V lead battery and ESS auxiliary battery (If equipped) must be charged at 100% independently from the read voltage. Record voltage on New Vehicle Prep (NVP) form.
Loose Attachments, Routing and Clearance	Inspect the following for routing, loose attachments, connections, and clearance. Reroute and tighten as required: Brake Lines, Fuel Lines, Power Steering Hoses, Vacuum Hoses, Clutch Lines, Refrigerant Lines, Wiring, Belts.
All Fluid Levels	Refer to the owner's manual or service information for proper fluid level inspection locations. Vehicles equipped with the eight-speed automatic transmission do not require the fluid to be checked. In addition, it is also not necessary to check the fluid of the manual transmission on Vipers and Challengers.
No Fluid Leaks present	Visually inspect the underhood area to verify that no fluid leaks exist. Check clamps for tightness and full engagement.

UNDER VEHICLE
Description	Action
No Fluid Leaks present	Raise the vehicle on an appropriate hoist and check the following: Loose Attachments, Routing Clearance and Damage, Absence of Fluid Leaks. Refer to Service Information for proper lift points. Check clamps for tightness and full engagement.
All Fluid Levels	Refer to the owner's manual or service information for proper fluid level inspection locations. Vehicles equipped with the eight-speed automatic transmission do not require the fluid to be checked. In addition, it is also not necessary to check the fluid of the manual transmission on Vipers and Challengers models. Also, do not top off the axle fluid on Ram 1500, Challenger, Charger, 300, Durango, and Grand Cherokee models.
Loose Attachments, Routing, Clearance, Damage	Raise the vehicle on an appropriate hoist and check the following: Loose Attachments, Routing Clearance and Damage, Absence of Fluid Leaks. Refer to Service Information for proper lift points. Check clamps for tightness and full engagement.

ROAD TEST/OPERATIONAL TEST
Description	Action
"Perform Road Test, Mileage: Before ______ After ______ NOTE: NOT REQUIRED ON VIPER.	Perform road test 3-5 mile (5-8 km) on a variety of road surfaces. Record mileage before and after road test.
Engine Starts with All Keys	Start vehicle with all sets of keys.
All Warning Lights and Gauges / No DTCs	Verify all warning lights and gauges are operating properly, and no fault codes exist.
Keyless Go/Key Sense	Verify that the vehicle starts with the push button, when key is inside vehicle.
Engine Starts Only in Park & Neutral	Verify engine will only start while automatic transmission is in park or neutral.
Engine Starts Only with Clutch Depressed	Verify engine will only start when clutch is depressed on manual transmission vehicles.
Service and Parking Brakes	Apply the service brakes while the vehicle is in motion. Be sure the brake operation is smooth and positive. Make sure the vehicle stops in a straight line and without pulling to one side. Verify that there is no shudder or vibration when braking. Verify that the parking brake is easy to operate. Make sure the parking brake does not drag.
Brake Transmission Shift Interlock	Verify that the vehicle will only start when the brake is pressed on vehicles with automatic transmission.
Clutch / Manual Transmission Shifting	Check for smooth shifting. Make sure shift lever operates easily and smoothly. Check for proper synchronization. The gears should not grind.
Automatic Transmission Shifting	Make sure that the park lock mechanism holds the vehicle. With the vehicle on a grade, put the automatic transmission in park and slowly release the service brake to check the operation of the park mechanism. Make sure the shift lever operates easily and smoothly. Check for smooth shifting. Check for proper upshifting and downshifting.
Start/Stop system (if equipped)	Verify that the Start/Stop function operates properly in different conditions (air conditioning system on, radio on/off, engine cold/hot); document any irregularities.
Verify LPG System Engagement (EMEA Only)	Verify LPG system engagement by performing the following: Start the engine Verify that the engine operates at a normal idle on gasoline fuel Verify that the system switches from gasoline to LPG Verify that the engine operates at a normal idle on LPG fuel (EMEA Only)
Engine Performance - Cold	The engine should: start properly, idle smoothly and at proper speed, be free from stumbling or hesitation, produce sufficient power, be free of unusual noises, operate within the proper temperature range, and stop when the ignition key is shut off or stop button is pressed.
Steering and Handling	Check that the power assist works properly. Make sure that the steering wheel does not vibrate abnormally at idle or road speed. Make sure that the steering wheel is centered when traveling in a straight line. Check that the vehicle does not drift to either side on flat road surfaces. Make sure that the vehicle does not vibrate or shake abnormally.
Noise, Vibration, Squeaks, or Rattles	Check that the vehicle is free of noise, vibrations, squeaks, or rattles. Tighten any loose fasteners.
Heater / Defrost- Front	Check the heater operation after the vehicle has reached operating temperature. Operate blower motor at all speeds. Operate the system in all modes. Check for hot air at all appropriate outlets. Check for temperature control operation.
Air Conditioning	Verify that the A/C system cools properly. Operate blower motor at all speeds. Check for cool air at all temperature outlets. Operate the system in all modes.
Defrost - Rear	Verify that the electric heated rear defroster operates correctly. Turn on and feel for warmth.
Blindspot Monitoring System (if equipped)	While on road test, verify that the visual warning indicators located on the side view mirrors are operating properly when an object is within the detection zone.
Cruise Control (if equipped)	Check the "on/off" switch. Check the "set" operation. Check the "resume" function. Check the "accelerate" and "decelerate" functions. Check the "cancel" button. Check the brake/clutch release function. If equipped, verify operation of Adaptive Cruise Control function.
Set Compass Variance / Calculation (if equipped)	Refer to the service information on TechCONNECT for information regarding compass setting procedures.
Transfer Case (if equipped)	Shift the transfer case through all ranges to make sure all shifting is smooth and operates properly.
Tire Pressure Monitoring System	Verify that Tire Pressure Monitoring Indicator Light is not illuminated when tires are above minimum inflation recommendations. Make sure that the indicator lamp is not flashing/chiming.
Engine Performance - Warm	The engine should: start properly, idle smoothly and at proper speed, be free from stumbling or hesitation, produce sufficient power, be free of unusual noises, operate within the proper temperature range, and stop when the ignition key is shut off or stop button is pressed.
Park Assist (if equipped)	Shift the vehicle into reverse and slowly back up toward an object. Verify that the Park Assist warning icon, lights and chimes operate properly as an object is approached.
Back-Up Camera (if equipped)	Shift the vehicle into reverse and verify that the display provides a clear and visible image from rear of vehicle.

INTERIOR
Description	Action
Visually Inspect Interior Parts for Damage, Fit, etc.	From the interior of the vehicle, open and close all doors to verify ease of operation. Fully open and close the glove box to verify proper operation. Fully open and close the console door to verify proper operation. Check that interior panels are fitted properly and free from damage.
All Interior Lamps and Horn	Operate and visually inspect all interior lights and switches, including: dome/map lamps, and if equipped the following: vanity mirror lamps, glove box lamps, ash tray lamp, cigar lighter lamp, radio lamps, door mounted lamps, illuminated entry system. Verify that the horn operates properly.
Rear View Mirror	Check that the rearview mirror day/night function is operating properly.
Front and Rear Wipers and Washers	Activate front windshield wipers, and if equipped, the rear window wipers. Verify proper operation at all speeds. Activate the front and if equipped, the rear washer. Check the spray pattern for proper operation and aim. Check the intermittent wipe feature for proper operation.
All interior Door Locks including Child Locks	Check all interior door locks for proper operation, including rear child safety door locks if equipped. Place in the unlocked position.
Steering Wheel Mounted Controls	Check all steering wheel controls for proper operation.
Cigar Lighter	Check cigar lighter for proper operation.
Power Windows and Window Lock Switch	Fully open and close all power windows to verify proper operation and sealing. Check that the windows operate properly at each door. Verify that window lock button is operating properly. Verify the operation of the "One Touch Up/Down" feature if equipped.
Outside Power Mirrors	Check power mirrors for proper operation.
Power Folding Outside Mirrors	Press the power folding mirror button on the driver side door trim panel. The switch is located between the left and right power mirror buttons.
Power Heated Mirrors (if equipped)	Check power heated mirrors for proper operation.
Seats and Seat Belts - All Adjustments	Check for correct installation and operation of seat and shoulder belts, and retractors. Check that the restraint system safety labels regarding the use of seatbelts and airbags are in place. Fully cycle the seats for proper adjustments and verify that each seat is securely mounted. Fold down and latch the rear seats. Pull forward to check that the latches operate correctly. Check for proper head restraint operation. NOTE: ON GRAND CHEROKEE AND DURANGO MODELS, MAKE SURE THE SECOND AND THIRD ROW SEAT BACKS ARE LEFT IN THE UPRIGHT POSITION AND THE SEAT BELTS ARE LEFT UNBUCKLED.
Power Sunroof (if equipped)	Cycle sunroof. Check that the sunroof opens and closes easily. Verify proper operation of the one touch open/close feature if equipped.
Set Clock(s)	Set all clocks to the correct time. Refer to the Owner's Manual for information regarding clock setting procedures.
Audio System	Turn the radio on and check reception in both AM and FM modes. Check that the CD player operates properly. Check for good sound quality from all speakers.
Telematic Box Module 2.0 (TBM)	Initialize Telematic Box Module. Note: Refer to Service Information for programming process.
Satellite Radio (if equipped)	Turn on satellite radio and verify reception.
Confirm UCONNECT Language Set To Market	Refer to User Guide to perform any radio updates/settings.
Confirm EVIC Set To Market Unit and Language	Refer to User Guide to perform any radio updates/settings. NOTE: ON 4C MODELS, SET LANGUAGE TO ENGLISH U.S. (NOT ENGLISH) FOR THE U.S. MARKET
GPS Navigation	Verify GPS Functions.
Cycle Glovebox Lock	Using the key, check that the glovebox lock operates properly.
Heated Steering Wheel (if equipped)	Verify that heated steering wheel is functioning properly.
Power Outlet(s)	Check all power outlets for proper operation.
Integrated Child Seat / Belt	Check the child restraints and child seats for proper operation.
Heated Seats (if equipped)	Check for proper operation of heated seats on all power levels, on all equipped seats.
Cargo Compartment Cover (if equipped)	Check the rear cargo compartment cover is operating properly.
Fuel Door Release	Activate the remote fuel door release to verify the fuel door will open.
Tilt/Telescoping Steering Column	Activate the manual/power tilt mechanism. Activate the telescoping feature of the steering column.
USB Outlets	Check all USB outlets for proper operation.

EXTERIOR
Description	Action
Inspect Body and Paint for Damage and Fit/ Finish	Inspect the body exterior for damage, loose or missing items. During the inspection, verify that no vehicle damage occurred between the time that the vehicle was received and the beginning of the New Vehicle Preparation. Note: DO NOT TOUCH UP MATTE PAINT OR CUSTOM COLORS.
Exterior Lamps - Headlamps, Turn Signals, Hazards, Park/Tail/License Plate, Trunk Lights, etc.	Operate and visually inspect the following: headlamps (high/low beams), turn signals, hazard warning flashers, parking/tail/license plate lamps, reverse/back up lamps, fog lamps, stop lamps including center mounted stop lamp, daytime running lamps (if equipped), clearance lamps, cargo bed lamps, any other lamps.
Lock and Unlock all doors with all mechanical keys	Verify all doors lock and unlock with all mechanical keys.
Doors, Liftgate and Tailgate- Adjust Strikers as Needed	Open each door/liftgate/tailgate from the outside to check outside door handle operation. Check the door detent. Partially close all doors to check the open-door detent. Close all doors/liftgates/tailgates to check the operation of latches and strikers. Adjust strikers as required. Verify liftgate/tailgate ease of operation.
Security Alarm Test (if equipped)	Lock doors using the Remote Keyless Entry Transmitter. Verify the operation of the Vehicle Security System warning lamp.
Remote Keyless Entry (if equipped)	Verify that doors unlock properly using all key FOBs.
Passive Entry/Keyless Go/Remote Proximity (if equipped)	Verify that the Keyless Enter-N-Go feature is operating properly, by grabbing the door handle of the locked vehicle, while the Remote Keyless Entry transmitter key is within 5 feet of the vehicle. The door should unlock automatically.
Remote Start (if equipped)	Verify that engine starts with all keys when using Remote Keyless Entry Transmitter.

VEHICLE STORAGE
Description	Action
Remove All Protective Transit Film From Body of Vehicle and Keep All Wheel Covers on Vehicle Until Sold	Remove all protective transit film from the body as soon as the vehicle arrives at the dealership. However, keep all wheel covers on the vehicle until sold.
Inflate tire pressure to max side wall pressure	Inflate tire pressure to maximum side wall pressure (except heavy duty trucks.) Periodically move vehicles to prevent flat spotting on tires.
Periodically move vehicles to prevent Flat Spotting on tires	Periodically move vehicles to prevent flat spotting on tires.
Periodically move vehicles to prevent corrosion on brake rotors	Periodically move vehicles to prevent corrosion on brake rotors. Refer to BRAKE ROTOR LOT ROT .
Disconnect the negative cable using the quick release lever.	Disconnect the negative cable using the quick release lever before storing the vehicle to conserve the battery.

FINAL DETAIL & INSPECTION
Description	Action
Inspect paint and body, touch up as needed	Make sure that the body is free from paint chips or scratches. Touch up any chips/scratches using thin layers of paint. Verify that the body is free from dings and dents. NOTE: ON VIPERS, DO NOT TOUCH UP MATTE PAINT OR CUSTOM COLORS.
Perform all incomplete recalls and RRTs (Print a current VIP Report)	Perform all incomplete recalls and RRTs (print a current VIP Report).
Reconnect the negative cable.	Reconnect the negative cable by securing the quick release lever.
Test and record battery state of charge	Check the battery state of charge by connecting a digital voltmeter at the jump-start locations. The battery voltage should be at least 12.4 volts (Fiat 500 BEV -100%). If charging is necessary, follow the service information procedures and recharge the battery. Record voltage on New Vehicle Prep (NVP) form.
Adjust tire pressures including spare to door placard	Adjust tire pressures including spare to door placard.
Confirm brake rotors do not have corrosion. Follow procedure in Service Information.	Refer to BRAKE ROTOR LOT ROT
Ensure Center Caps are Installed	Verify that all center caps are installed.
Remove interior and exterior Transportation Protective Covers	Remove exterior protective coatings/coverings from vehicle, remove interior protective covers, grease markings on door jambs, unnecessary labels, etc.
Wash and clean vehicle exterior	Wash the entire vehicle. Clean the tire sidewalls and wheel/wheel covers (use non - acidic wheel cleaner). Clean exterior/interior glass surfaces.
Clean vehicle interior	Inspect the interior trim, seats, carpeting, and moldings. Clean as necessary.