Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECK FOR AN ACTIVE DTC
1. Turn the ignition on.
2. Using the scan tool, erase PCM DTCs.
3. Using the scan tool, navigate to Actuator Tests and actuate the Variable Swirl Valve.
4. Using the scan tool, view PCM DTCs.
  Did this DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT DTC .
CHECK THE (N117) INTAKE SWIRL VALVE CONTROL CIRCUIT FOR A SHORT TO VOLTAGE

Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the Intake Swirl Valve jumper harness connector.
3. Turn the ignition on.
4. Measure the voltage on the (N117) Intake Swirl Valve Control circuit at the Intake Swirl Valve jumper harness connector.
  Is there any voltage present?
  
  Yes
  - Go To 3
  No
  - Repair the (N117) Intake Swirl Valve Control circuit for a short to voltage.
  - Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
CHECK THE (N117) INTAKE SWIRL VALVE CONTROL CIRCUIT FOR A SHORT TO THE (F343) ASD RELAY OUTPUT CIRCUIT

Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the PCM C2 harness connector.
3. Measure the resistance between the (N117) Intake Swirl Valve Control circuit and the (F343) ASD Relay Output circuit at the Intake Swirl Valve jumper harness connector.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (N117) Intake Swirl Valve Control circuit for a short to the (F343) ASD Relay Output circuit.
  - Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
CHECK THE INTAKE SWIRL VALVE FOR PROPER OPERATION
1. Reconnect the PCM C2 harness connector.
2. Connect a jumper between ground and the (N117) EGR Air Flow Control Valve Control circuit at the Intake Swirl Valve jumper harness connector (main harness side).
3. Turn the ignition on.
4. Using the scan tool, navigate to Actuator Tests and toggle the Intake Swirl Valve.
5. Using the scan tool, view PCM DTCs.
  NOTE:
  The scan tool should display a P2009-Intake Manifold Runner (Swirl) Control Circuit Low DTC as active or pending with the jumper in place.
  
  Did the scan tool display the DTC as describe above?
  
  Yes
  - Replace the Intake Manifold in accordance with the service information.
    NOTE:
    Before replacing the Intake Swirl Valve, carefully inspect the jumper harness and connectors for damage. If any damage is found, replace the jumper harness.
  - Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
  No
  - Go To 5
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
  No
  - Repair the poor connections.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to PCM VERIFICATION TEST .