Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECK FOR AN ACTIVE DTC
1. Ignition on, engine not running.
2. With the scan tool, erase DTCs in the PCM.
3. Monitor the scan tool for at least two minutes.
4. Cycle the ignition key off and on several times, leaving the ignition on for at least 10 seconds at a time.
5. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE MAF/INTAKE AIR SENSOR FOR PROPER OPERATION
1. With the scan tool, erase DTCs.
2. Turn the ignition off.
3. Disconnect the MAF/Intake Air Sensor harness connector.
4. Turn the ignition on.
5. With the scan tool, select View DTCs.
  NOTE:
  The scan tool should display a P0113-00-Intake Air Temperature Sensor High DTC as active or pending with the connector disconnected.
  
  Does the scan tool display the DTC as described above?
  
  Yes
  - Replace the Mass Air Flow/Intake Air Sensor in accordance with the service information. Refer to SENSOR, MASS AIRFLOW (MAF), REMOVAL .
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (K362) INTAKE AIR TEMPERATURE SIGNAL CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the PCM C1 harness connector.
3. Measure the resistance between ground and the (K362) Intake Air Temperature Signal circuit at the MAF/Intake Air Sensor harness connector.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (K362) Intake Air Temperature Signal circuit for a short to ground.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK FOR THE (K362) INTAKE AIR TEMPERATURE SIGNAL CIRCUIT SHORTED TO THE (K757) SENSOR GROUND CIRCUIT
1. Measure the resistance between the (K362) Intake Air Temperature Signal circuit and the (K757) Sensor Ground circuit at the MAF/Intake Air Sensor harness connector.
  Is the resistance above 10k Ohms?
  
  Yes
  - Go To 5
  No
  - Repair the (K362) Intake Air Temperature Signal circuit for a short to the (K757) Sensor Ground circuit.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Repair the poor connections.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .