Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECK FOR AN ACTIVE DTC
1. Ignition on, engine not running.
2. With the scan tool, record the environmental conditions and record the DTCs on the repair order.
3. With the scan tool, erase DTCs in the PCM.
4. Cycle the ignition key off and on several times, leaving the ignition on for at least 10 seconds at a time.
5. Start the engine and let it run for two minutes.
6. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (K69) IAT 3 SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the engine off. Leave the ignition off.
2. Disconnect the IAT Sensor 3 harness connector.
3. Ignition on, engine not running.
4. Measure the voltage on the (K69) IAT 3 Signal circuit at the IAT Sensor 3 harness connector.
  Is the voltage above 5.2 Volts?
  
  Yes
  - Repair the (K69) Intake Air Temperature 3 Signal circuit for a short to voltage.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (K69) IAT 3 SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the PCM C1.harness connector.
3. Measure the resistance of the (K69) IAT 3 Signal circuit between the IAT Sensor 3 harness connector and the PCM C1 harness connector.
  Is the resistance above 5.0 Ohms?
  
  Yes
  - Repair the (K69) Intake Air Temperature 3 Signal circuit for an open/high resistance.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE (K64) RETURN CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Measure the resistance of the (K64) Return circuit between the IAT Sensor 3 harness connector and the PCM C1 harness connector.
  Is the resistance above 5.0 Ohms?
  
  Yes
  - Repair the (K64) Return circuit for an open/high resistance.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK THE IAT SENSOR 3 FOR PROPER OPERATION
1. Replace the Intake Air Temperature Sensor 3 in accordance with the service information. Refer to SENSOR, BOOST PRESSURE, REMOVAL .
2. Turn the ignition on.
3. With the scan tool, erase PCM DTCs.
4. Perform several ignition key cycles leaving the ignition on for at least 10 seconds per cycle.
5. Start the engine and let it run for two minutes.
6. With the scan tool, read PCM DTCs.
  Does the scan tool display this DTC?
  
  Yes
  - Go To 6
  No
  - Test complete.
  - Perform the PCM VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Repair the poor connections.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .