LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2018 >> Grand Cherokee Laredo, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 27 (5.7L Engine (Service Information)) >> Cylinder Head >> Installation >> Installation - Left Cylinder Head

Installation - Left Cylinder Head

WARNING: This page is about a different variant/trim than selected.
GC0132214Courtesy of CHRYSLER GROUP, LLC
  1. If replacing the cylinder head, transfer the valves, valve seals and valve springs to the new cylinder head. Refer to VALVES, INTAKE AND EXHAUST, INSTALLATION . If valve refacing is necessary. Refer to STANDARD PROCEDURE - REFACING .
  2. If replacing the cylinder head, transfer the exhaust manifold to the new cylinder head. Using the sequence shown in the illustration, tighten the exhaust manifold bolts/studs to 25 N.m (18 ft. lbs.).
  3. If replacing the cylinder head, transfer the spark plugs to the new cylinder head. Refer to SPARK PLUG, INSTALLATION .
    GC0088040Courtesy of CHRYSLER GROUP, LLC

    Right side shown in the illustration, left side similar. 

    CAUTION:

    The cylinder head gaskets are not interchangeable between the left and right sides. They are marked with an "L" and "R" to indicate the left or right side and they are marked "TOP" to indicate which side goes up.

  4. Using a suitable solvent, clean all sealing surfaces of the cylinder block and cylinder heads.
    GC0080293Courtesy of CHRYSLER GROUP, LLC

    Right side shown in the illustration, left side similar. 

  5. Position the new cylinder head gasket (1) onto the cylinder block.
  6. Position the cylinder head (2) onto the cylinder head gasket (1) and cylinder block.
    GC0088039Courtesy of CHRYSLER GROUP, LLC

    Right side shown in the illustration, left side similar. 

  7. Using the sequence shown in the illustration, tighten the cylinder head bolts 1 through 10 to 34 N.m (25 ft. lbs.).
  8. Using the sequence shown in the illustration, tighten the cylinder head bolts 11 through 15 to 20 N.m (15 ft. lbs.).
  9. Again, using the sequence shown in the illustration, tighten the cylinder head bolts 1 through 10 to 54 N.m (40 ft. lbs.).
  10. Again, using the sequence shown in the illustration, tighten the cylinder head bolts 11 through 15 to 20 N.m (15 ft. lbs.).
  11. Again, using the sequence shown in the illustration, rotate the cylinder head bolts 1 through 10 90°.
  12. Again, using the sequence shown in the illustration, tighten the cylinder head bolts 11 through 15 to 34 N.m (25 ft. lbs.).
    GC0081766Courtesy of CHRYSLER GROUP, LLC

    Right side shown in the illustration, left side similar. 

  13. Using Pushrod Retainer (special tool #9070, Retainer, Push Rod) (1), install the push rods and rocker arms in their original location as noted during removal. Refer to ROCKER ARM, VALVE, INSTALLATION 
    GC0080292Courtesy of CHRYSLER GROUP, LLC
    NOTE:

    Right side shown in the illustration, left side similar. 

  14. Install the cylinder head cover. Refer to COVER(S), CYLINDER HEAD, INSTALLATION .
    GC0095568Courtesy of CHRYSLER GROUP, LLC
  15. Install the intake manifold. Refer to MANIFOLD, INTAKE, INSTALLATION .
    GC0146023Courtesy of CHRYSLER GROUP, LLC
  16. Install the cowl cover panel. Refer to COVER, COWL PANEL, INSTALLATION .
  17. Install the air cleaner and resonator assembly. Refer to BODY, AIR CLEANER, INSTALLATION .
  18. Fill the cooling system. Refer to STANDARD PROCEDURE .
    GC0143807Courtesy of CHRYSLER GROUP, LLC
  19. Change the engine oil and engine oil filter. Refer to CAPACITIES AND RECOMMENDED FLUIDS, SPECIFICATIONS .
  20. Install the engine cover (2).
  21. Install the oil fill cap (1).
  22. Connect the negative battery cable.
    NOTE:

    This vehicle is equipped with an engine oil change indicator system. The "Oil Change Required" message will need to be reset after changing the engine oil and filter.

  23. Reset the "Oil Change Required" indicator system. Refer to CENTER, ELECTRONIC VEHICLE INFORMATION, STANDARD PROCEDURE .
  24. Start the engine check for leaks.
scientia non olet · About LEMON Manuals