LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2018 >> Grand Cherokee Laredo, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (8HP75 Automatic Transmission (Service Information)) >> Valve Body >> Installation

Valve Body: Installation

WARNING: This page is about a different variant/trim than selected.
CAUTION:

The Transmission Control Module (TCM), or Transmission Control Module Assembly (TCMA) is extremely sensitive to Electrostatic Discharge (ESD). Always use a ground strap and follow the ESD guidelines in ELECTROSTATIC DISCHARGE (ESD) SENSITIVE DEVICES. Failure to follow these instructions may result in damage to the TCM/TCMA.

GC0152241Courtesy of CHRYSLER GROUP, LLC
  1. Install the fluid port (1) with NEW  O-rings (2) and seal (3) to the valve body.
    GC0162906Courtesy of CHRYSLER GROUP, LLC
  2. Install one of the valve body (special tool #10379, Pins, Valve Body Alignment) (3) in the rear of the transmission as shown as a guide.
    NOTE:

    Make sure the speed sensor at the rear of the valve body does get caught between the valve body and the transmission case when positioning the valve body to the case. 

  3. Carefully guide the front of the valve body over the cradle while aligning the rear of the valve body with the alignment pin.
    GC0162910Courtesy of CHRYSLER GROUP, LLC
  4. Install the front alignment pin (1).
  5. Use an appropriate tool on one of the alignment pins to assist in holding the valve body in position while installing the remaining fasteners.
    GC0169780Courtesy of CHRYSLER GROUP, LLC
  6. Install the valve body assembly retaining bolts not including 16-18 and hand tighten.
  7. Remove the pins and install the remaining bolts.
    GC0158349Courtesy of CHRYSLER GROUP, LLC
  8. Lower the transmission back onto the crossmember.
  9. Install the rear mount nuts (2) and tighten to the proper specification. Refer to TORQUE SPECIFICATIONS  .
    GC0152117Courtesy of CHRYSLER GROUP, LLC
  10. Using (special tool #10377, Remover/Installer, Guide Sleeve) (1) carefully install the electrical harness insulator (2) to the transmission case (3).
    GC0152103Courtesy of CHRYSLER GROUP, LLC
  11. Lock the electrical connector lock (2) to the internal harness end.
  12. Install the speed sensor (4) to the case install the retaining bolt (1) and tighten to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
    GC0154626Courtesy of CHRYSLER GROUP, LLC
  13. If equipped, install the Hydraulic Impulse Oil Storage (H.I.S.) accumulator (1).
  14. Tighten the bolts (2 and 3) to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
  15. Connect the H.I.S. electrical connector.
  16. Install the valve body assembly end retainer bolts (3) and hand tighten.
    GC0169780Courtesy of CHRYSLER GROUP, LLC
  17. Tighten the valve body fasteners to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
    GC0158366Courtesy of CHRYSLER GROUP, LLC
  18. Remove the tie strap (3).
  19. Attach the Manual Park Release (MPR) cable (1) to the MPR lever (2).
    GC0152239Courtesy of CHRYSLER GROUP, LLC
  20. Install the oil pan and gasket.
  21. Install the thirteen oil pan retaining bolts and tighten the fasteners to the proper using the sequence given. Refer to TECHNICAL SPECIFICATIONS .
    GC0152193Courtesy of CHRYSLER GROUP, LLC
  22. Connect the plug connector (1).
    GC0152192Courtesy of CHRYSLER GROUP, LLC
  23. Turn the locking mechanism (1) of the harness plug clockwise and lock in place.
  24. If the valve body is replaced, program the TCM. Refer to MODULE, TRANSMISSION CONTROL (TCM), MODULE PROGRAMMING .
  25. Perform the TRANSMISSION FILL AFTER SERVICE procedure. Refer to FLUID AND FILTER, STANDARD PROCEDURE .
  26. Perform the TRANSMISSION VERIFICATION TEST. Refer to TRANSMISSION VERIFICATION TEST .
scientia non olet · About LEMON Manuals