Diagnostic Test

WARNING: This page is about a different car, the 2017 Jeep Cherokee. However, it is still accessible from the selected car via links, so may be relevant.

IDENTIFYING VEHICLE EQUIPMENT
NOTE:
Make sure the battery is fully charged.

NOTE:
The use of an approved special tool or Digital Multimeter such as a Fluke Meter that will not apply more than 20 milliamperes to a circuit are the only measurement tools to be used.

NOTE:
Probing of the circuit cavities at the ORC Module C1 or C2 body harness connectors is only to be done with a approved test lead from the (special tool #10159, Test Leads, Dedicated). Or a comparable test lead to prevent vehicle wiring harness connector damage during diagnostic procedures.
1. Turn the ignition on.
2. With the scan tool, read ORC active DTCs.
  Does the scan tool display active DTC: B00C5-11-PASSENGER SEAT TRACK POSITION SENSOR - CIRCUIT SHORT TO GROUND?
  
  Yes
  - Go To 2.
  No
  - Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Refer to RESTRAINTS SYSTEM INTERMITTENT TEST .
CHECK FOR ACTIVE INTERNAL FAULTS, IGNITION FAULTS, AND BATTERY FAULTS IN THE OCCUPANT RESTRAINT CONTROLLER (ORC)
1. With the scan tool, read Occupant restraint Controller (ORC) DTCs.
  Does the scan tool display any active DTCs relating to internal faults, ignition faults, or battery faults?
  
  Yes
  - Diagnose and repair the DTCs. Refer to OCCUPANT RESTRAINT CONTROLLER (ORC) - DIAGNOSTIC CODE INDEX .
  No
  - Go To 3
INSPECT PASSENGER SEAT HARNESS WIRES AND CONNECTORS
WARNING:
Turn the ignition off, disconnect the battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Using the wiring diagram/schematic as a guide, inspect the passenger seat harness wiring and connectors. Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated terminals.
  Are any of these conditions present?
  
  Yes
  
  NOTE:
  Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
  - Replace the passenger seat harness in accordance with the Service Information.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  No
  - Go To 4
VERIFY THAT PASSENGER SEAT HARNESS IS ROUTED CORRECTLY
1. Verify that the passenger seat harness is routed correctly.
  Is the Driver Seat Harness routed correctly?
  
  Yes
  - Go To 5
  No
  - Reroute the passenger seat harness as necessary.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
CHECK (R730) PASSENGER SEAT DETECTION RETURN CIRCUIT AND (R264) PASSENGER SEAT POSITION SENSOR VOLTAGE CIRCUIT FOR A SHORT TO GROUND
1. Measure the resistance between ground and the (R730) Passenger Seat Detection Return circuit.
2. Measure the resistance between ground and the (R264) Passenger Seat Position Sensor Voltage circuit.
  Is the resistance below 10k Ohms on either circuit?
  
  Yes
  
  NOTE:
  Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
  - Replace the Passenger Seat Harness in accordance with the service information.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  No
  - Go To 6
CHECK (R730) PASSENGER SEAT DETECTION RETURN CIRCUIT AND (R264) PASSENGER SEAT POSITION SENSOR VOLTAGE CIRCUIT FOR AN OPEN
1. Disconnect the ORC harness connectors.
2. Connect the test leads to the DVOM.
3. Measure the resistance of the (R730) Passenger Seat Detection Return circuit between the ORC module body harness connector cavity C2 19 and the Passenger Seat Track Position Sensor connector cavity 1.
4. Measure the resistance of the (R264) Passenger Seat Position Sensor Voltage circuit between the ORC module body harness connector cavity C2 33 and the Passenger Seat Track Position Sensor connector cavity 2.
  Is the resistance of either circuit above 5.0k Ohms?
  
  Yes
  
  NOTE:
  Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.
  - Replace the Passenger Seat Harness in accordance with the Service Information.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .
  No
  
  WARNING:
  Turn the ignition off, disconnect the battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
  
  WARNING:
  If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment.
  - Replace the Occupant Restraint Controller (ORC) in accordance with the service information. Refer to MODULE, OCCUPANT RESTRAINT CONTROLLER, REMOVAL .
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to RESTRAINTS SYSTEM VERIFICATION TEST .