LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2017 >> Wrangler Sahara, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 78 (Transmission Control Module (TCM) - DTCS P0219-00 To P1B13-00) >> DTC Troubleshooting >> P0711-00-Transmission Fluid Temperature Sensor A Circuit Range-Performance >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2017 Jeep Cherokee. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR ENGINE COOLING DTCS 
    1. With the scan tool, read all DTCs and record on the repair order.

      Are any engine cooling or Active Grille Shutter (AGS) DTCs set?

      Yes 

      No 

      • Go To  2
  2. CHECK FOR OTHER TRANSMISSION DTCS 
    NOTE:

    Before performing this Diagnostic Test, be certain that there are no problems that could cause the Transmission to overheat. Check for restricted transmission oil cooler and lines, air flow restrictions, and low transmission fluid. Towing loads weighing more than the recommended towing capacity could cause excessively high transmission temperatures.

    1. With the scan tool, read all DTCs.

      Are there any other TCM DTCs set?

      Yes 

      No 

      • Go To  3
  3. CHECK FOR AN ACTIVE DTC 
    1. Record the Event Data and Environmental Data.
    2. With the scan tool, erase DTCs.
    3. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    4. With the scan tool, read TCM DTCs.

      Did the DTC return?

      Yes 

      • Go To  4

      No 

  4. CHECK TRANSMISSION TEMPERATURE SENSOR CIRCUITS FOR HIGH RESISTANCE 
    1. Turn the ignition off.
    2. Disconnect the TCM harness connector.
    3. Remove the Transmission side cover and disconnect the Transmission temperature sensor harness connector.
    4. Connect a jumper wire between the (T54) Transmission Temperature Signal circuit and the (T820) Sensor Ground circuit at the transmission temperature sensor harness connector.
    5. Measure resistance between (T54) Transmission Temperature Signal circuit and the (T820) Sensor Ground circuit at the TCM harness connector.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  5

      No 

      • Repair the (T54) Transmission Temperature Signal circuit or the (T820) Sensor Ground circuit for an open or high resistance.
      • Perform the TRANSMISSION VERIFICATION TEST. Refer to TRANSMISSION VERIFICATION TEST - 948TE 9HP48 .
  5. CHECK TRANSMISSION TEMPERATURE SENSOR CIRCUITS FOR A SHORT TO GROUND 
    1. With the jumper wire still connected, check for continuity between ground and the (T54) Transmission Temperature Signal circuit at the TCM harness connector.

      Is there continuity between ground and the (T54) Transmission Temperature Signal circuit?

      Yes 

      No 

      • Go To  6
  6. CHECK THE (T54) TRANSMISSION TEMPERATURE SIGNAL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT 
    1. Remove the jumper wire from the Transmission Temperature Sensor harness connector.
    2. Check for continuity between the (T54) Transmission Temperature Signal circuit and all other circuits at the TCM harness connector.

      Is there continuity between the (T54) Transmission Temperature Signal circuit and any other circuit?

      Yes 

      No 

      • Go To  7
  7. CHECK THE (T820) SENSOR GROUND CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT 
    1. Check for continuity between the (T820) Sensor Ground circuit and all other circuits at the TCM harness connector.

      Is there continuity between the (T820) Sensor Ground circuit and any other circuit?

      Yes 

      No 

      • Go To  8
  8. VERIFY TRANSMISSION TEMPERATURE SENSOR RESISTANCE / TEMPERATURE CORRELATION 
    1. Measure the resistance between (T54) Transmission Temperature Signal terminal and (T820) Sensor Ground terminal at the Transmission Temperature Sensor.
      TEMPERATURE vs RESISTANCE
      TEMPERATURE  RESISTANCE 
      -30°C (-22°F) 37, 400 - 50, 600 Ohms
      10°C (50°F) 5, 810 - 7, 100 Ohms
      110°C (230°F) 231 - 263 Ohms
      145°C (293°F) 105 - 117 Ohms

      Using the chart above, compare the Temperature Sensor temperature to the correlating resistance value.

      Is the resistance within the specified range when the sensor is at the given temperature?

      Yes 

      • Go To  9

      No 

  9. CHECK RELATED HARNESS CONNECTIONS 
    1. Disconnect all TCM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the Transmission Assembly harness connector.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Perform a terminal drag test on each connector terminal to verify proper terminal tension.

      Repair any conditions that are found.

    5. Connect all TCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    10. With the scan tool, read TCM DTCs.

      Did the DTC return?

      Yes 

      No 

scientia non olet · About LEMON Manuals