Torque Specifications
WARNING: This page is about a different car, the 2017 Jeep Cherokee. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Access Plate to Transmission Bolt | 9 | - | 80 | |
| Battery Negative Cable to Auto Transmission Bolt | 24 | 17 | - | |
| Bell to Intermediate Plate | 12 | 9 | ||
| Drain Plug to Trans Case | 35 | 26 | ||
| Electric Power Steering (EPS) Ground to Transmission - M8 Bolt | 22 | 16 | - | |
| EPS Ground to Transmission - M6 Bolt | 10 | - | 88 | |
| Engine Oil Pan to Transmission Bell Housing | 63.5 | 47 | ||
| Engine to Transmission - M10 Bolts | 50 | 37 | - | |
| Engine to Transmission - M12 Bolts | 93 | 69 | - | |
| Driveplate To Crankshaft | 110 | 81 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Flexplate to Torque Converter Bolts | 40 | 30 | - | |
| Front Differential Bracket to Isolator Bolt | 120 | 88 | - | |
| Heat Shield to PTU Bolts | 8 | - | 71 | |
| Lever to Transmission Shaft Bolt | 19 | 14 | - | |
| Park Holder to Clutch Cover | 66 | 47 | ||
| Pivot Bracket to Transmission Bolts | 160 | 118 | - | |
| Power Transfer Unit to Transmission Flange Bolts | 48 | 35 | - | |
| Rear Differential Bracket to Isolator Bolts | 120 | 88 | - | |
| Shift Cable Bracket to Transmission - M6 X 1.0 X 20.0 Bolt | 10 | - | 88 | |
| Shift Cable Bracket to Transmission - M6 X 1.00 X 14.00 Bolt | 10 | - | 88 | |
| Shifter Plate to Floor Pan Bolts | 8 | - | 71 | |
| Torque Strut Bracket to Transmission Bolts | 163 | 120 | - | |
| Transmission Bracket to Transmission - M6 Bolt | 10 | - | 88 | |
| Transmission Bracket to Transmission - M12 Bolt | 105 | 77 | - | |
| Transmission to Engine - M10 Bolts | 50 | 37 | - | |
| Transmission to Engine - M12 X 1.25 X 50.0 Bolts | 115 | 85 | - | |
| Transmission to Engine - M12 X 1.25 X 97.1 Bolts | 63 | 46 | - | |
| Bell to Case Bolts | 25 | 18 | - | |
| Bell Housing Plug | 12 | - | 106 | |
| Bell Housing to Bearing Support | 25 | 18 | - | |
| Oil Baffle to Bellhousing | 10 | - | 88 | |
| Cover Plate to Valve Body Screws | 6 | - | 53 | |
| Cover to Case Bolts | 11 | - | 97 | |
| Detent Spring to Case Bolts | 11 | - | 97 | |
| Detent Spring to Park Holder | 6 | - | 53 | |
| Detent Spring to Park Holder | 6 | - | 53 | |
| Dog A Washer to Dog A Inner Piston | 2.8 | - | 25 | |
| Oil Supply Tube Bolts | 10.1 | - | 89 | |
| Oil Cooler to Transmission | 25 | 18 | ||
| Oil Fill Plug | 23 | 17 | ||
| Oil Pan to Block | 10 | 88 | ||
| Solenoid Retaining Plate to Valvebody | 6 | 53 | ||
| Output Gear Support to Gear Bearing | 60 | 44 | ||
| Pan to Case- Oil Bolts | 9.5 | - | 84 | |
| Park Guide Bolts | 4 + 21° | - | 35 + 21° | |
| Park Support to Case Bolts | 12.5 | - | 111 | |
| Ring Gear to Differential Bolts | 10 | - | 88 | |
| Valve Body Bolts | 6 | - | 53 | |
| Valve Body to Case Bolts | 8 | - | 71 | |
| Bolt and Washer Assembly - Bellhousing to Bearing Support | 25 | 18 | - | |
| Nut - Stake | 60 | 49 | - | |
| Oil Baffle to Bellhousing Screws | 10 | - | 88 | |
| Drain Plug | 35 | 26 | - | |
| Screw TC Anti-Rotation Plug | 8 | - | 71 | |
| Cover Plate to Valvebody | 6 | - | 53 | |
| Oil Cooler Line Fitting Assembly | 30 | 22 | - | |
| Oil Fill Plug | 23 | 17 | - | |
| Screw - Dog A Washer to Dog A Inner Piston | 2.8 | - | 25 | |
| Filter to Pump Support Screws | 10 | - | 88 | |
| Intermediate Plate to Bell Screws | 10 | - | 88 | |
| Sensor Assembly Solenoid Connector Bar to Valve Body Screws | 6 | - | 53 | |
| Solenoid Retaining Plate to Valve Body Screw | 6 | - | 53 | |
| Speed Sensor to Transmission Case Bolt | 5.5 | - | 49 | |
| Torx Valve Body to Case | 8 | - | 71 | |
| Trans Bracket to Trans | 110 | 81 | - | |
| Trans Mount to Rail | 101 | 75 | - | |
| Trans Mount to Trans | 118 | 87 | - | |
| Trans to Engine | 63.5 | 47 | - | |
| TCU to Case | 20 | 15 | - | |
| Wire Retention Plate Screws | 5.5 | - | 49 | |
| Shift Cable Adjuster Screw | 8 | - | 71 | |
| Bell to Case Bolts | 25 | 18 | - | |
| Bell Housing Plug | 12 | - | 106 | |
| Bell Housing to Bearing Support | 25 | 18 | - | |
| Oil Baffle To Bellhousing | 10 | - | 88 | |
| Cover Plate to Valve Body Screws | 6 | - | 53 | |
| Cover to Case Bolts | 15 | 11 | - | |
| Detent Spring to Case Bolts | 11 | - | 97 | |
| Detent Spring to Park Holder | 6 | - | 53 | |
| Detent Spring to Park Holder | 6 | - | 53 | |
| Dog A Washer to Dog A Inner Piston | 2.8 | - | 25 | |
| Oil Supply Tube Bolts | 10.1 | - | 89 | |
| Oil Cooler to Transmission | 25 | 18 | ||
| Oil Fill Plug | 23 | 17 | ||
| Oil Pan to Block | 10 | 88 | ||
| Solenoid Retaining Plate to Valvebody | 6 | 53 | ||
| Output Gear Support to Gear Bearing | 60 | 44 | ||
| Pan to Case- Oil Bolts | 9.5 | - | 84 | |
| Park Guide Bolts | 4 + 21° | - | 35 + 21° | |
| Park Support to Case Bolts | 12.5 | - | 111 | |
| Ring Gear to Differential Bolts | 10 | - | 88 | |
| Valve Body Bolts | 6 | - | 53 | |
| Valve Body to Case Bolts | 8 | - | 71 | |
| Bolt and Washer Assembly - Bellhousing to Bearing Support | 25 | 18 | - | |
| Nut - Stake | 60 | 49 | - | |
| Oil Baffle to Bellhousing Screws | 10 | - | 88 | |
| Drain Plug | 35 | 26 | - | |
| Screw TC Anti-Rotation Plug | 8 | - | 71 | |
| Cover Plate to Valvebody | 6 | - | 53 | |
| Oil Cooler Line Fitting Assembly | 30 | 22 | - | |
| Oil Fill Plug | 23 | 17 | - | |
| Screw - Dog A Washer to Dog A Inner Piston | 2.8 | - | 25 | |
| Filter to Pump Support Screws | 10 | - | 88 | |
| Intermediate Plate to Bell Screws | 10 | - | 88 | |
| Sensor Assembly Solenoid Connector Bar to Valve Body Screws | 6 | - | 53 | |
| Solenoid Retaining Plate to Valve Body Screw | 6 | - | 53 | |
| Speed Sensor to Transmission Case Bolt | 5.5 | - | 49 | |
| Torx Valve Body to Case | 8 | - | 71 | |
| Trans Bracket to Trans | 110 | 81 | - | |
| Trans Mount to Rail | 101 | 75 | - | |
| Trans Mount to Trans | 118 | 87 | - | |
| Trans to Engine | 63.5 | 47 | - | |
| TCU to Case | 20 | 15 | - | |
| Wire Retention Plate Screws | 5.5 | - | 49 |