Diagnostic Test

WARNING: This page is about a different car, the 2014 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR AN ACTIVE DIAGNOSTIC TROUBLE CODE (DTC)
NOTE:
A disconnected sensor will set this DTC. Verify the Park Assist Sensor is connected before proceeding with this diagnostic procedure.
1. Turn the ignition on.
2. With the scan tool, read DTCs.
  Does the scan tool display this DTC as active?
  
  Yes
  - Go To 2
  No
  - Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals, and correct pin tension.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE VOLTAGE OF THE (X700) PARK ASSIST SENSOR SUPPLY CIRCUIT

Fig 1: Checking Voltage Of Park Assist Sensor Supply Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the Park Assist Sensor harness connector.
3. Turn the ignition on.
4. Measure the voltage of the (X700) Park Assist Sensor Supply circuit.
  Is the voltage above 8.0 volts?
  
  Yes
  - Go To 4
  No
  - Go To 3
CHECK THE (X700) PARK ASSIST SENSOR SUPPLY CIRCUIT FOR AN OPEN OR HIGH RESISTANCE

Fig 2: Checking Park Assist Sensor Supply Circuit For An Open Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the Park Assist Module C2 harness connector.
3. Measure the resistance of the (X700) Park Assist Sensor Supply circuit.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Replace the Park Assist Module in accordance with the Service Information. Refer to MODULE, PARK ASSIST, REMOVAL .
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Repair the open or high resistance in the (X700) Park Assist Sensor Supply circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (D704) PARK ASSIST SENSOR 10 SIGNAL CIRCUIT FOR A SHORT TO GROUND WITH THE PARK ASSIST MODULE CONNECTED

Fig 3: Checking Park Assist Sensor Signal Circuit For A Short To Ground
Courtesy of CHRYSLER GROUP, LLC

NOTE:
Perform this step with the Park Assist Module connected.
1. Measure the resistance between ground and the (D704) Park Assist Sensor 10 Signal circuit.
  Is the resistance below 10K Ohms?
  
  Yes
  - Go To 5
  No
  - Go To 7
CHECK THE (D704) PARK ASSIST SENSOR 10 SIGNAL CIRCUIT FOR A SHORT TO GROUND WITH THE PARK ASSIST MODULE DISCONNECTED

Fig 4: Checking Park Assist Sensor Signal Circuit For A Short To Ground
Courtesy of CHRYSLER GROUP, LLC
1. Disconnect the Park Assist Module C2 harness connector.
2. Measure the resistance between ground and the (D704) Park Assist Sensor 10 Signal circuit.
  Is the resistance below 10K Ohms?
  
  Yes
  - Repair the short to ground in the (D704) Park Assist Sensor 10 Signal circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 6
CHECK THE (D704) PARK ASSIST SENSOR 10 SIGNAL CIRCUIT FOR A SHORT TO THE (X750) PARK ASSIST SENSOR GROUND CIRCUIT

Fig 5: Checking Park Assist Sensor Signal Circuit For A Short To Park Assist Sensor Ground Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance between the (D704) Park Assist Sensor 10 Signal circuit and the (X750) Park Assist Sensor Ground circuit.
  Is the resistance below 10K Ohms?
  
  Yes
  - Repair the short between the (D704) Park Assist Sensor 10 Signal circuit and the (X750) Park Assist Sensor Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Replace the Park Assist Module in accordance with the Service Information. Refer to MODULE, PARK ASSIST, REMOVAL .
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (D704) PARK ASSIST SENSOR 10 SIGNAL CIRCUIT FOR AN OPEN

Fig 6: Checking Park Assist Sensor Signal Circuit For Open
Courtesy of CHRYSLER GROUP, LLC
1. Disconnect the Park Assist Module C2 harness connector.
2. Measure the resistance of the (D704) Park Assist Sensor 10 Signal circuit.
  Is the resistance above 5.0 Ohms?
  
  Yes
  - Repair the open in the (D704) Park Assist Sensor 10 Signal circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 8
PARK ASSIST SENSOR

Fig 7: Park Assist Sensor Connector End View
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition on.
2. Reconnect the Park Assist Module C2 harness connector.
3. Connect a jumper wire across the (X700) Park Assist Sensor Supply and (D704) Park Assist Sensor 10 Signal circuits.
4. Turn the ignition on.
5. With the scan tool, read DTCs.
  Does the scan tool display DTC: B1297-12-PTS SENSOR 10 - CIRCUIT SHORT TO BATTERY as active?
  
  Yes
  - Replace the Park Assist Sensor in accordance with the Service Information. Refer to SENSOR, PARK ASSIST, REMOVAL .
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Replace the Park Assist Module in accordance with the Service Information. Refer to MODULE, PARK ASSIST, REMOVAL .
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .