Diagnostic Test

WARNING: This page is about a different car, the 2014 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.

VERIFY THAT DTC U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION SENSOR 4 IS ACTIVE
NOTE:
Make sure the battery is fully charged.
1. Turn the ignition on.
2. With the scan tool, read ORC DTCs.
  Does the scan tool display active: U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION SENSOR 4?
  
  Yes
  - Go To 2
  No
  - Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Refer to STANDARD PROCEDURE .
CHECK THE (R141), (R161) RIGHT SIDE IMPACT SENSOR 4 SIGNAL AND GROUND CIRCUITS FOR A SHORT TO VOLTAGE

Fig 1: Checking Right Side Impact Sensor 4 Signal And Ground Circuits For A Short To Voltage
Courtesy of CHRYSLER GROUP, LLC

WARNING:
Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Disconnect the Right Side Impact Sensor 4 harness connector.
2. Disconnect the ORC harness connector.
3. If equipped with the standard key ignition, use this ignition on warning.
  WARNING:
  Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
4. If equipped with the keyless ignition, use this ignition on warning.
  WARNING:
  Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
5. Measure the voltage of the (R141) Right Side Impact Sensor 4 Signal circuit and (R161) Sensor Ground circuit at the appropriate terminal of the Right Side Impact Sensor harness connector and ground.
  Is there any voltage present?
  
  Yes
  - Repair the (R140), (R160) Right Side Impact Sensor 4 circuits for a short to voltage.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 3
CHECK THE (R141) RIGHT SIDE IMPACT SENSOR 4 SIGNAL CIRCUIT FOR A SHORT TO GROUND

Fig 2: Checking Right Side Impact Sensor 4 Signal Circuit For A Short To Ground
Courtesy of CHRYSLER GROUP, LLC

WARNING:
Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
1. Measure the resistance of the (R141) Right Side ImpacT Sensor 4 Signal circuit between the appropriate terminal of the Right Side Impact Sensor 4 harness connector and ground.
  Is the resistance below 20 Ohms?
  
  Yes
  - Repair the (R141) Right Side Impact Sensor 4 Signal circuit for a short to ground.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 4
CHECK THE (R141), (R161) RIGHT SIDE IMPACT SENSOR 4 CIRCUITS FOR A SHORT TOGETHER

Fig 3: Checking Right Side Impact Sensor 4 Circuits For A Short Together
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance between the (R141) Right Side Impact Sensor 4 Signal circuit and the (R161) Sensor Ground circuits at the Right Side Impact Sensor 4 harness connector.
  Is the resistance below 20 Ohms?
  
  Yes
  - Repair the (R141), (R161) Right Side Impact Sensor 4 circuits shorted together.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 5
CHECK THE (R161) RIGHT SIDE IMPACT SENSOR 4 GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE

Fig 4: Checking Right Side Impact Sensor 4 Ground Circuit For An Open Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Connect the (special tool #8443-28, SRS Load Tool Adapter) to the Occupant Control Module harness connector.
2. Measure the resistance of the (R161) Right Side Impact Sensor 4 Ground circuit between the Right Side Impact Sensor 4 harness connector and the appropriate terminal of the (special tool #8443-28, SRS Load Tool Adapter).
  Is the resistance below 1 Ohm?
  
  Yes
  - Go To 6
  No
  - Repair the (R161) Right Side Impact Sensor 4 Ground circuit for an open or high resistance.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK THE (R141) RIGHT SIDE IMPACT SENSOR 4 SIGNAL CIRCUIT FOR AN OPEN OR HIGH RESISTANCE

Fig 5: Checking Right Side Impact Sensor 4 Signal Circuit For An Open Or High Resistance
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance of the (R141) Right Side Impact Sensor 4 Signal circuit between the a Right Side Impact Sensor 4 harness connector and the appropriate terminal of the (special tool #8443-28, SRS Load Tool Adapter).
  Is the resistance below 1 Ohm?
  
  Yes
  - Go To 7
  No
  - Repair the (R141) Right Side Impact Sensor 4 Signal circuit for an open or high resistance.
  - Perform the RESTRAINTS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK OPERATION OF THE RIGHT SIDE IMPACT SENSOR 4
1. Replace the Right Side Impact Sensor. Refer to SENSOR, IMPACT, REMOVAL .
2. Reconnect the vehicle body harness to the impact sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
4. If equipped with the standard key ignition, use this ignition on warning.
  WARNING:
  Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
5. If equipped with the keyless ignition, use this ignition on warning.
  WARNING:
  Disconnect the 12-volt battery wait two minutes before proceeding, remove the ORC fuses, connect the 12-volt battery, wait two minutes before proceeding. Cycle the ignition to the On position, then reconnect the ORC fuses. Wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
6. Connect the scan tool to the Data Link Connector - use the most current software available.
7. Use the scan tool and erase the stored codes in all airbag system modules.
8. Turn the Ignition Off, and wait five seconds before turning the Ignition On.
9. Wait one minute, and read active codes and if there are none present read the stored codes.
  Did the active: U11B0-LOST COMMUNICATION W/RIGHT SIDE SATELLITE IMPACT SENSOR 4 DTC return?
  
  Yes
  
  WARNING:
  Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
  
  WARNING:
  If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment. Failure to follow these instructions may result in possible serious or fatal injury.
  - Replace the Occupant Restrain Controller (ORC) in accordance with the Service Information. Refer to MODULE, OCCUPANT RESTRAINT CONTROLLER, REMOVAL .
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Repair is complete.
  - Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .