LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2014 >> Wrangler Sahara, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 189 ((Totally Integrated Power Module (TIPM) - Electrical Diagnostics)) >> DTC Troubleshooting >> U0001-Can C Bus Circuit >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2016 Jeep Wrangler and 2015 Jeep Wrangler. However, it is still accessible from the selected car via links, so may be relevant.
  1. TEST FOR INTERMITTENT CONDITION 
    1. Turn the ignition on.
    2. Using the scan tool, record and erase TIPM DTCs.
    3. Cycle the ignition from on to off three times.
    4. Turn the ignition on.
    5. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  2

      No 

      • The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
  2. ANTILOCK BRAKE MODULE - INTERNAL SHORT 
    1. Turn the ignition off.
    2. Disconnect the Antilock Brake Module harness connector.
    3. Turn the ignition on.
    4. Using the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  3

      No 

      • Inspect the wiring and connectors for damage or shorted circuits in accordance with the Service Information.
      • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  3. POWERTRAIN CONTROL MODULE - INTERNAL SHORT 
    1. Turn the ignition off.
    2. Disconnect the Powertrain Control Module C1 or C2 (Diesel) harness connector.
    3. Turn the ignition on.
    4. Using the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  4

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace and program the Powertrain Control Module in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  4. TRANSMISSION CONTROL MODULE - INTERNAL SHORT 
    1. Turn the ignition off.
      NOTE:

      If vehicle is not equipped with this module, answer yes to the question.

    2. Disconnect the Transmission Control Module harness connectors.
    3. Turn the ignition on.
    4. Using the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  5

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace and program the Transmission Control Module in accordance with the Service Information.
      • Perform the NAG1 TRANSMISSION VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  5. STEERING ANGLE SENSOR - INTERNAL SHORT 
    1. Turn the ignition off.
      NOTE:

      If vehicle is not equipped with this module, answer yes to the question.

    2. Disconnect the Steering Angle Sensor harness connector.
    3. Turn the ignition on.
    4. Using the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  6

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace the Steering Angle Sensor in accordance with the Service Information.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  6. AUTOMATIC SWAY BAR SYSTEM MODULE - INTERNAL SHORT 
    1. Turn the ignition off.
      NOTE:

      If vehicle is not equipped with this module, answer yes to the question.

    2. Disconnect the Automatic Sway Bar System Module harness connector.
    3. Turn the ignition on.
    4. Using the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  7

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace the Automatic Sway Bar System Module in accordance with the Service Information.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  7. ELECTRIC GEAR SHIFT MODULE - INTERNAL SHORT 
    1. Turn the ignition off.
      NOTE:

      If vehicle is not equipped with this module, answer yes to the question.

    2. Disconnect the Electric Gear Shift Module harness connector.
    3. Turn the ignition on.
    4. With the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. With the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  8

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace the Automatic Sway Bar System Module in accordance with the Service Information.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  8. WIRELESS CONTROL MODULE - INTERNAL SHORT 
    1. Turn the ignition off.
    2. Disconnect the Wireless Control Module harness connector.
    3. Turn the ignition on.
    4. Using the scan tool, record and erase TIPM DTCs.
    5. Cycle the ignition from on to off three times.
    6. Turn the ignition on.
    7. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  9

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace the Wireless Control Module in accordance with the Service Information.
      • Perform the WIRELESS CONTROL MODULE (WCM) VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  9. OCCUPANT RESTRAINT CONTROLLER - INTERNAL SHORT 
    1. Turn the ignition off.
      WARNING:

      Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    2. Disconnect the Occupant Restraint Controller harness connectors.
      WARNING:

      Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    3. Using the scan tool, record and erase TIPM DTCs.
    4. Cycle the ignition from on to off three times.
    5. Turn the ignition on.
    6. Using the scan tool, read active TIPM DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  10

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace the Occupant Restraint Controller in accordance with the Service Information.
      • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  10. CHECK THE (D64) CAN C BUS (-) CIRCUIT FOR A SHORT TO VOLTAGE 
    Fig 1: Measuring Voltage Between CAN C Bus (-) Circuit & Ground
    GC0101326Courtesy of CHRYSLER GROUP, LLC
    1. Measure the voltage between the (D64) CAN C Bus (-) circuit and ground.

      Is there any voltage present?

      Yes 

      • Repair the short to voltage in the (D64) CAN C Bus (-) circuit.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  11
  11. CHECK THE (D65) CAN C BUS (+) CIRCUIT FOR A SHORT TO GROUND 
    Fig 2: Measuring Resistance Between Ground & CAN C Bus (+) Circuit
    GC0101327Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Measure the resistance between ground and the (D65) CAN C Bus (+) circuit.

      Is any resistance present?

      Yes 

      • Repair the short to ground in the (D65) CAN C Bus (+) circuit.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  12
  12. CHECK THE (D65) CAN C BUS (+) CIRCUIT FOR A SHORT TO (D64) CAN C BUS (-) CIRCUIT 
    Fig 3: Measuring Resistance Between CAN C Bus (+) Circuit & CAN C Bus (-) Circuit
    GC0101329Courtesy of CHRYSLER GROUP, LLC
    1. Measure the resistance between the (D65) CAN C Bus (+) circuit and the (D64) CAN C Bus (-) circuit.

      Is any resistance present?

      Yes 

      • Repair the short between the (D65) CAN C Bus (+) circuit and the (D64) CAN C Bus (-) circuit.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Inspect the wiring and connectors for damage or shorted circuits. If OK, replace and program the Totally Integrated Power Module in accordance with the Service Information.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
scientia non olet · About LEMON Manuals