Diagnostic Test

WARNING: This page is about a different car, the 2016 Dodge Journey and 2015 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.

CHECK IF THE DTC P0882 IS CURRENT
1. With the scan tool, Check the Starts Since Set counter for P0882.
  NOTE:
  This counter only applies to the last DTC set.
  
  Is the Starts Since Set counter equal to 0?
  
  Yes
  - Go To 2
  No
  - Go To 7
CHECK PCM/TCM RELAY
1. Install subsitue PCM/TCM Relay.
2. Ignition on, engine not running.
3. With the scan tool, read the Voltage Sense (gas engines) or Switched Battery voltage (diesel engines).
  Does the Voltage Sense (gas engines) or Switched Battery voltage (diesel engines) read battery voltage?
  
  Yes
  - Replace the Transmission Control Relay.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
  No
  - Go To 3
CHECK THE FUSED B+ CIRCUITS

Fig 1: Measuring Voltage Of The Fused B+ Circuits
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off to the lock position.
2. Remove the Transmission Control Relay.
3. Ignition on, engine not running.
4. Using a 12-volt test light connected to ground, check the both Fused B+ Feed circuits in the Transmission Control Relay connector.
  Does the test light illuminate brightly on both terminals?
  
  Yes
  - Go To 4
  No
  - Repair the Fused B+ circuit(s) for an open or loss of voltage.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
CHECK THE (T16) TRANSMISSION CONTROL OUTPUT CIRCUIT FOR AN OPEN

Fig 2: Checking Transmission Control Output Circuit For An Open
Courtesy of CHRYSLER GROUP, LLC
1. Using a fused jumper wire, jumper the PCM/TCM relay connector from Fused B(+) to the Transmission Control Output.
2. Using a 12-volt test light connected to ground, check the (T16) Transmission Control Output circuits in the PCM C1 harness connector.
  Does the test light illuminate brightly on all terminals?
  
  Yes
  - Go To 5
  No
  - Repair the (T16) Transmission Control Output circuit(s) for an open.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
CHECK THE (T16) TRANSMISSION CONTROL OUTPUT CIRCUIT FOR A SHORT TO GROUND

Fig 3: Checking Transmission Control Output Circuit For A Short To Ground
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off to the lock position.
2. Remove jumper from the PCM/TCM relay connector.
3. Measure the resistance of the (T16) Transmission Control Output circuits between ground and the PCM C1 harness connector.
  Is the resistance above 100k Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the (T16) Transmission Control Output circuit for a short to ground.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
CHECK THE (T15) TRANSMISSION CONTROL CIRCUIT FOR AN OPEN

Fig 4: Checking Transmission Control Circuit For An Open
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance of the (T15) Transmission Control circuit between the PCM C1 harness connector and the PCM/TCM Relay connector in the PDC.
  Is the resistance above 5.0 Ohms?
  
  Yes
  - Repair the (T15) Transmission Control circuit for an open.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
  No
  - Using the schematics as a guide, check the Powertrain Control Module (PCM) terminals for corrosion, damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems are found, replace and program the PCM in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL . With the scan tool, perform Quick Learn.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
CHECK THE WIRING AND CONNECTORS
1. The conditions necessary to set this DTC are not present at this time.
2. Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.
3. Wiggle the wires while checking for shorted and open circuits.
4. With the scan tool, check the Event Data to help identify the conditions in which the DTC was set.
  Where there any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the 62TE VERIFICATION TEST. Refer to 62TE TRANSMISSION VERIFICATION TEST .
  No
  - Test Complete.