Diagnostic Test

WARNING: This page is about a different car, the 2016 Dodge Journey and 2015 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.

ACTIVE DTC
1. Turn the ignition off.
2. If possible, allow the vehicle to sit with the ignition off for more than 480 minutes in an environment where the temperature is consistent and above -7°C (19.4°F).
3. Test drive the vehicle. The vehicle must exceed 48 km/h (30 mph) during the test drive. Do not cycle the ignition off when the test drive is completed.
4. With the scan tool, select View DTCs.
  Is the DTC Active or Pending at this time?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION . .
ENGINE COOLANT TEMPERATURE
1. Turn the ignition off.
2. Allow the vehicle to sit with the ignition off in an environment where the temperature is consistent and above -7°C (19.4°F) until the engine coolant temperature is equal to ambient temperature.
3. Turn the ignition on.
4. With the scan tool, compare the AAT, ECT and IAT sensor values.
  Is the Engine Coolant Temperature Sensor value within 10°C (18°F) of the other two sensor values?
  
  Yes
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION . .
  No
  - Go To 3
ECT SENSOR VOLTAGE
1. Turn the ignition off.
2. Disconnect the Engine Coolant Temperature Sensor harness connector.
3. Turn the ignition on.
4. With the scan tool, read the Engine Coolant Temperature Sensor voltage.
  NOTE:
  The sensor voltage should be approximately 5.0 Volts (plus or minus.1 Volt) with the connector disconnected.
  
  Does the scan tool display the voltage as described above?
  
  Yes
  - Go To 4
  No
  - Go To 5
ECT SENSOR

Fig 1: Engine Coolant Temperature Sensor Harness Connector Terminal Identification
Courtesy of CHRYSLER GROUP, LLC
1. With the scan tool, read the Engine Coolant Temperature Sensor voltage.
2. Connect a jumper wire between the (K2) ECT Signal circuit and the (K900) Sensor Ground circuit in the Engine Coolant Temperature Sensor harness connector.
  NOTE:
  The sensor voltage should be approximately 0.0 Volts (plus or minus.1 Volt) with the jumper wire in place.
  
  Does the scan tool display the voltage as described above?
  
  Yes
  - Replace the ECT Sensor in accordance with the service information. Refer to SENSOR, COOLANT TEMPERATURE, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
  No
  - Go To 5
    NOTE:
    Remove the jumper wire before continuing.
EXCESSIVE RESISTANCE IN THE (K2) ECT SIGNAL CIRCUIT
1. Turn the ignition off.
2. Using a Voltmeter perform a voltage drop test. Backprobe the (K2) ECT Signal circuit at the ECT Sensor harness connector and probe the PCM C2 harness connector. Make sure the Voltmeter leads are connected so a positive polarity is displayed on the Voltmeter.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
3. Start the engine and allow it to reach normal operating temperature.
4. Monitor the Voltmeter.
  Is the voltage below 0.5 Volt?
  
  Yes
  - Go To 6
  No
  - Repair the open or excessive resistance in the (K2) ECT Signal circuit.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
EXCESSIVE RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
1. Turn the ignition off.
2. Move the Voltmeter leads to backprobe the (K900) Sensor Ground circuit at the ECT Sensor harness connector and to probe the PCM C2 harness connector. Make sure the Voltmeter leads are connected so a positive polarity is indicated on the Voltmeter.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
3. Start the engine and allow it to reach normal operating temperature.
4. Monitor the Voltmeter.
  Is the voltage below 0.5 Volt?
  
  Yes
  - Go To 7
  No
  - Repair the open or excessive resistance in the (K900) Sensor ground circuit.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the ECT Sensor and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the ECT Sensor and Powertrain Control Module connectors.
4. Perform any Technical Service Bulletins that may apply.
  Were there any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
  No
  - Replace and program the Powertrain Control Module in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .