LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2014 >> Wrangler Sahara, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 157 (Audio/Video - Non-DTC Based Diagnostics) >> Diagnosis And Testing >> Diagnosis And Testing - Rear Camera Inoperative >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2016 Dodge Journey and 2015 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.
  1. VERIFY OPERATION OF THE TGW AND BACKUP LAMPS 
    1. Verify the operation of the TGW and Backup Lamps.

      Do the TGW and Backup Lamps operate correctly?

      Yes 

      • Go To  2

      No 

      • Diagnose any problems with the TGW and Backup Lamps.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  2. CHECK THE (F923) FUSED RUN RELAY OUTPUT CIRCUIT 
    Fig 1: Checking Fused Run Relay Output Circuit
    GC0150289Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Apply the parking brake.
    3. Disconnect the Rear Camera Assembly Harness Connector.
    4. Turn the ignition on.
    5. Measure the voltage between the (F923) Fused Run Relay Output circuit and ground.

      Is battery voltage present?

      Yes 

      • Go To  3

      No 

      • Repair the (F923) Fused Run Relay Output circuit for an open or short to ground.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  3. CHECK THE (Z911) GROUND CIRCUIT 
    Fig 2: Checking Ground Circuit
    GC0150290Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Measure the resistance between ground and the (Z911) Ground Circuit.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  4

      No 

      • Repair the (Z911) Ground circuit for an open.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  4. CHECK THE (X970) CAMERA SIGNAL, THE (X971) RETURN, AND THE (X972) SHIELD CIRCUITS FOR AN OPEN CIRCUIT 
    Fig 3: Checking Camera Signal, The Return, And The Shield Circuits For An Open Circuit
    GC0150291Courtesy of CHRYSLER GROUP, LLC
    1. Disconnect the Telematics Gateway (TGW) C3 harness connector.
    2. Measure the resistance of the (X970) (X971) and (X972) circuits between the Rear Camera harness connector and Telematics Gateway (TGW) C3 harness connectors.

      Is the resistance below 5.0 Ohms on the (X970) (X971) or (X972) circuits?

      Yes 

      • Go To  5

      No 

      • Repair the appropriate circuit for an open.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  5. CHECK THE (X970) CAMERA SIGNAL, THE (X971) RETURN, AND THE (X972) SHIELD CIRCUITS SHORTED TO GROUND 
    Fig 4: Checking Camera Signal, The Return, And The Shield Circuits Shorted To Ground
    GC0150305Courtesy of CHRYSLER GROUP, LLC
    1. Measure the resistance between ground and the (X970) (X971) and (X972) circuits.

      Is the resistance below 5.0 Ohms on the (X970) (X971) or (X972) circuits?

      Yes 

      • Repair the appropriate circuit for a short to ground.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Replace the License Plate Lamp/Rear Camera Assembly in accordance with the Service Information. Refer to CAMERA, REMOVAL .
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
scientia non olet · About LEMON Manuals