Diagnostic Test
WARNING: This page is about a different car, the 2016 Dodge Journey and 2015 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.
- CHECK FOR AN ACTIVE DTC NOTE:
After the repairs have been made, verify proper O2 Sensor operation. If all the O2 Sensor voltage readings have not returned to normal, follow the diagnostic procedure for the remaining O2 Sensors.
NOTE:Check for contaminants that may have damaged the O2 Sensor: contaminated fuel, unapproved silicone, oil and coolant.
- Start the engine.
- Test drive or operate the vehicle in accordance with the when monitored and set conditions.
- With the scan tool, read DTCs and record on the repair order.
Is the DTC active or pending?
Yes
- Go To 2
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION . .
- CHECKING THE EXHAUST SYSTEM FOR LEAKS
- Perform the CHECKING THE EXHAUST SYSTEM FOR LEAKS test procedure. Refer to CHECKING THE EXHAUST SYSTEM FOR LEAKS
.
Were any exhaust leaks found?
Yes
- Perform the appropriate repairs.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
No
- Go To 3
- Perform the CHECKING THE EXHAUST SYSTEM FOR LEAKS test procedure. Refer to CHECKING THE EXHAUST SYSTEM FOR LEAKS
.
- CHECK THE (K243) O2 SENSOR 2/2 SIGNAL CIRCUIT
- Turn the ignition off
- Disconnect the O2 Sensor 2/2 harness connector.
- Turn the ignition on.
- Measure the voltage on the (K243) O2 Sensor 2/2 Signal circuit in the O2 Sensor 2/2 harness connector.
Is the voltage between 4.1 and 5.0 volts?
Yes
- Go To 4
No
- Check the (K243) O2 Sensor 2/2 Signal circuit for a short to ground, open or short to voltage. If OK, replace and program the Powertrain Control Module in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
- CHECK THE (K904) O2 SENSOR 2/2 RETURN CIRCUIT
- Measure the voltage on the (K904) O2 Sensor 2/2 Return circuit in the O2 Sensor 2/2 harness connector.
Is the voltage at 2.5 volts?
Yes
- Go To 5
No
- Check the (K904) O2 Sensor 2/2 Return circuit for a short to ground, open or short to voltage. If OK, replace and program the Powertrain Control Module in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
- Measure the voltage on the (K904) O2 Sensor 2/2 Return circuit in the O2 Sensor 2/2 harness connector.
- OXYGEN SENSOR NOTE:
Check for signs of contaminants that may have damaged the O2 Sensor, such as contaminated fuel, unapproved silicone, oil and coolant.
- Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Oxygen Sensor 2/2 and the Powertrain Control Module (PCM).
- Look for any chafed, pierced, pinched or partially broken wires.
- Look for broken, bent, pushed out or corroded terminals.
- Perform any Service Bulletins that may apply.
Were any problems found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .
No
- Replace the Oxygen Sensor 2/2 in accordance with the Service Information. Refer to OXYGEN SENSOR, REMOVAL .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST . .