Operating Modes

Following are paragraphs that briefly describe the operation of each of the Vehicle Theft Alarm (VTA) operating modes.

• Enabling  - The TIPM must have the VTA function electronically enabled in order for the VTA to perform as designed. The logic in the TIPM keeps its VTA function dormant until it is enabled using a diagnostic scan tool. The VTA function of the TIPM is enabled on vehicles equipped with the VTA option at the factory, but a service replacement TIPM must be VTA-enabled by the dealer using a diagnostic scan tool. Refer to the appropriate diagnostic information.
• Arming  - Passive arming of the VTA occurs when the vehicle is exited with the key removed from the ignition switch, the headlamps are turned Off, and the doors are locked while they are open using the power lock switch. Active arming occurs when the Lock button on the Remote Keyless Entry (RKE) transmitter is depressed to lock the vehicle. For active arming to occur, the doors must be closed and the ignition switch must be in the Off position when the RKE transmitter Lock button is depressed. The power lock switch will not function if the key is in the ignition switch or the headlamps are turned On with the driver side front door open.

  Pre-arming of the VTA is initiated when a door is open when the vehicle is locked using a power door lock switch or when the RKE transmitter Lock button is depressed. Pre-arming will not occur if the key is in the ignition switch or the headlamps are turned On with the driver side front door open. When the VTA is pre-armed, the arming sequence is delayed until all of the doors have been closed. The VTA will remain in pre-armed mode for up to 16 seconds after all doors have been closed.

  Once the VTA begins the passive or active arming sequence, the security indicator in the instrument cluster will flash rapidly for about 16 seconds. This indicates that VTA arming is in progress. If the ignition switch is turned to the On position, if a door or the swing gate is unlocked or opened by any means, or if the RKE Panic button (if equipped) is depressed during the 16 second arming process, the security indicator will stop flashing and the arming process will abort. Once the arming sequence is successfully completed, the security indicator will flash at a slower rate, indicating that the VTA is armed.

  For the swing gate and the hood of vehicles equipped with the hood ajar switch, the VTA arming sequence will occur regardless of whether the swing gate or the hood is open or closed, but the security indicator will illuminate solid and the swing gate or under hood area will not be protected until the swing gate or the hood is closed. Also, if the status of the swing gate ajar or the hood ajar switch changes from open to closed during the 16 second arming process, the security indicator will switch from solid to flashing and the VTA arming sequence will abort. Once the arming process is successfully completed, the security indicator will flash at a slower rate, indicating that the VTA is armed.

• Disarming  - For vehicles built for the North American market, passive disarming of the VTA occurs by inserting a valid Sentry Key Immobilizer System (SKIS) key into the ignition lock cylinder or by turning the ignition switch to the On position. Active disarming of the VTA for all markets occurs when the vehicle is unlocked by depressing the Unlock button of the RKE transmitter. Once the alarm has been activated, either disarming method will also deactivate the alarm. Depressing the Panic button (if equipped) on the RKE transmitter will not  disarm the VTA.
• Alarm  - The VTA alarm output varies by the version of the VTA with which the vehicle is equipped. In all cases, the alarm provides both visual and audible outputs; however, the time intervals of these outputs vary by the requirements of the market for which the vehicle is manufactured. In all cases, the visual output will be a flashing On and Off of the exterior lamps. For vehicles equipped with the North American or the export base version of the VTA, the audible output will be a pulsing of the horn. For vehicles with the export premium version of the VTA, the audible output will be a cycling of the alarm siren in addition to the pulsing horn. The inputs that will trigger the alarm include the ignition switch, the door ajar switches, the swing gate ajar switch and, in vehicles built for certain markets where they are required, the hood ajar switch and the intrusion module.
• Power-Up Mode  - When the armed VTA senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode, the alarm system remains armed following a battery failure or disconnect. If the VTA was armed prior to a battery disconnect or failure, the technician or vehicle operator will have to actively or passively disarm the alarm system after the battery is reconnected. The power-up mode will also apply if the battery goes dead while the system is armed, and battery jump-starting is attempted. The VTA will be armed until the technician or vehicle operator has actively or passively disarmed the alarm system. If the VTA is in the disarmed mode prior to a battery disconnect or failure, it will remain disarmed after the battery is reconnected or replaced, or if jump-starting is attempted.
• Tamper Alert  - The VTA tamper alert feature will pulse the horn three times upon VTA disarming if the alarm was triggered and has since timed out. This feature alerts the vehicle operator that the VTA alarm was activated while the vehicle was unattended.
• Intrusion Alarm  - The intrusion alarm is an exclusive feature of the export premium version of the VTA, which is only available in certain markets where it is required. When the VTA is armed, the intrusion module uses hard wired outputs to control two (two-door vehicles) or three (four-door vehicles) microwave intrusion sensors which allow the module to monitor the interior of the vehicle for movement. If motion is detected, the intrusion module sends an electronic message to the TIPM over the CAN data bus to invoke the visual alarm features, and sends an electronic message to the alarm siren in the engine compartment over a dedicated serial bus to invoke the audible alarm feature.

  The motion detect feature of the intrusion module can be disabled by depressing the Lock button on the RKE transmitter 3 times within 15 seconds during VTA arming, while the security indicator is still flashing rapidly. The VTA provides a single short siren chirp as an audible confirmation that the motion detect disable request has been received.

  The intrusion module must be electronically enabled in order for the intrusion alarm to perform as designed. The intrusion alarm function of the intrusion module is enabled on vehicles equipped with this option at the factory, but a service replacement module must be configured and enabled by the dealer using a diagnostic scan tool. Refer to the appropriate diagnostic information. The intrusion module monitors the condition of the intrusion sensors as well as the siren, and will store fault information in the form of a Diagnostic Trouble Code (DTC) if a system malfunction is detected. The intrusion module may be diagnosed, and any stored DTC can be retrieved using a diagnostic scan tool. Refer to the appropriate diagnostic information.