Diagnostic Test

TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
  NOTE:
  Make sure the Ignition Off Draw (IOD) fuse is installed and battery voltage is between 10.0 and 16.0 volts.
2. Using the scan tool, select ECU View.
  NOTE:
  A red "X" will be next to the module that is not communicating, indicating that the module is not active on the Bus network. A green check indicates that the module is active on the Bus network.
  
  NOTE:
  Check the TIPM for any active CAN C hardware DTCs, perform DTC before proceeding.
  
  Does the scan tool display a red "X" next to the module?
  
  Yes
  - Go To 2
  No
  - The no response condition is not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring for chafed, pierced, pinched and partially broken wires and the wiring harnessconnectors for broken, bent, pushed out and corroded terminals.
(A959) FUSED B(+) CIRCUIT OPEN OR SHORTED

Fig 1: Checking Fused B(+) Circuit For Open Or Short
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the Final Drive Control Module (ASBS) harness connector.
3. Using a 12-volt test light connected to ground, check each (A959) Fused B(+) circuit.
  Does the test light illuminate brightly for each circuit?
  
  Yes
  - Go To 3
  No
  - Repair the (A959) Fused B(+) circuit for an open or short.
  - Perform the ASBS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
(Z905) GROUND CIRCUIT OPEN

Fig 2: Checking Ground Circuit Using 12-Volt Test Light Connected To 12 Volts
Courtesy of CHRYSLER GROUP, LLC
1. Using a 12-volt test light connected to 12-volts, check the (Z905) ground circuit.
  Does the test light illuminate brightly?
  
  Yes
  - Go To 4
  No
  - Repair the (Z905) ground circuit for an open.
  - Perform the ASBS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
(F943) FUSED RUN/START RELAY OUTPUT CIRCUIT OPEN OR SHORTED

Fig 3: Checking Fused Run/Start Relay Output Circuit For Open Or Short
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition on.
2. Using a 12-volt test light connected to ground, check the (F943) Fused Run/Relay Output circuit.
  Does the test light illuminate brightly?
  
  Yes
  - Go To 5
  No
  - Repair the (F943) Fused Run/Relay Output circuit for an open or short.
  - Perform the ASBS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
(D65) CAN C BUS (+) CIRCUIT OPEN

Fig 4: Measuring Resistance Of CAN C Bus (+) Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Turn the ignition off.
2. Disconnect the TIPM C1 harness connector.
3. Measure the resistance of the (D65) CAN C Bus (+) circuit between the TIPM C1 harness connector and the Final Drive Control Module (ASBS) connector.
  Is resistance below 5.0 ohms?
  
  Yes
  - Go To 6
  No
  - Repair the (D65) CAN C Bus (+) circuit for an open.
  - Perform the ASBS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
(D64) CAN C BUS (-) CIRCUIT OPEN

Fig 5: Measuring Resistance Of CAN C Bus (-) Circuit
Courtesy of CHRYSLER GROUP, LLC
1. Measure the resistance of the (D64) CAN C Bus (-) circuit between the TIPM C1 harness connector and the Final Drive Control Module (ASBS) connector.
  Is resistance below 5.0 ohms?
  
  Yes
  - Replace the Final Drive Control Module (ASBS) in accordance with the Service Information.
  - Perform the ASBS VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Repair the (D64) CAN C Bus (-) circuit for an open.
  - Perform the ASBS VERIFICATION TEST. Refer to STANDARD PROCEDURE .