LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2008 >> Commander Base, 3.7 K, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 5 (545RFE Automatic Transmission (Service Information)) >> Automatic Transmission - 545RFE - Service Information >> Body-Valve >> Assembly >> Valve Body

Valve Body

WARNING: This page is about a different variant/trim than selected.
Fig 1: Exploded View Of Valve Body Components
GC0005312Courtesy of CHRYSLER LLC
1 - LOW/REVERSE ACCUMULATOR 6 - OVERDRIVE ACCUMULATOR
2 - LOW/REVERSE SHUTTLE VALVE AND PLUG 7 - UNDERDRIVE ACCUMULATOR
3 - UPPER VALVE BODY 8 - 4C ACCUMULATOR
4 - MANUAL VALVE 9 - 2C ACCUMULATOR
5 - SOLENOID SWITCH VALVE AND PLUGS -
  1. Lubricate valves and the housing valve bores with clean transmission fluid.
  2. Install solenoid switch valve and plugs (5) and manual valve (4) into the valve body.
  3. Install the retainers to hold each valve into the valve body.
    Fig 2: Check Ball Locations
    GC0005313Courtesy of CHRYSLER LLC
  4. Install the valve body check balls into their proper locations.
  5. Position the separator and transfer plate onto the valve body.
  6. Install the screws to hold the transfer plate to the valve body. Tighten the screws to 6 N.m (50 in. lbs.).
    Fig 3: Exploded View Of Valve Body Components
    GC0005312Courtesy of CHRYSLER LLC
    1 - LOW/REVERSE ACCUMULATOR 6 - OVERDRIVE ACCUMULATOR
    2 - LOW/REVERSE SHUTTLE VALVE AND PLUG 7 - UNDERDRIVE ACCUMULATOR
    3 - UPPER VALVE BODY 8 - 4C ACCUMULATOR
    4 - MANUAL VALVE 9 - 2C ACCUMULATOR
    5 - SOLENOID SWITCH VALVE AND PLUGS -
  7. Install the accumulator pistons (1, 6-9) and springs into the valve body in the location from which they were removed. Note that all accumulators except the overdrive have two springs. The overdrive accumulator piston (6) has only one spring.
  8. Install the Low/Reverse shuttle valve, plug and retainer (2) into the valve body housing.
  9. Position the accumulator cover onto the valve body.
  10. Install the screws to hold the accumulator cover onto the valve body. Tighten the screws to 7 N.m (60 in. lbs.).
    Fig 4: Valve Body External Components
    GC0005314Courtesy of CHRYSLER LLC
    1 - TRS SELECTOR PLATE
    2 - DETENT SPRING
    3 - CLUTCH PASSAGE SEALS
  11. Install the TRS selector plate (1) onto the valve body and the manual valve.
  12. Position the detent spring (2) onto the valve body.
  13. Install the screw to hold the detent spring (2) onto the valve body. Tighten the screw to 4.5 N.m (40 in. lbs.).
  14. Install new clutch passage seals (3) onto the valve body, if necessary.
    Fig 5: Transmission Solenoid/TRS Assembly Bolts
    GC0005311Courtesy of CHRYSLER LLC
    1 - SOLENOID PACK BOLTS (15)
  15. Install the solenoid and pressure switch assembly onto the valve body.
  16. Install the bolts (1) to hold the solenoid and pressure switch assembly onto the valve body. Tighten the bolts to 6 N.m (50 in. lbs.). Tighten the bolts adjacent to the arrows cast into the bottom of the transfer plate first.
scientia non olet · About LEMON Manuals