LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2005 >> Wrangler Rubicon, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 492 (Automatic Transmission Diagnostic Procedures) >> Diagnostic Information And Procedures >> Transmission - RFE - Diagnostic Tests >> P0712-Transmission Temperature Sensor Low >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2005 Jeep Liberty. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC TEST REFERENCE - P0712-TRANSMISSION TEMPERATURE SENSOR LOW

TEST ACTION APPLICABILITY
1
NOTE: Low fluid level can be the cause of many transmission problems. If the fluid level is low locate and repair the leak then check and adjust the fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid false symptoms.
With the DRBIII®, read the engine DTC's. Check and repair all engine DTC's prior to performing transmission symptom diagnostics.With the DRBIII®, read Transmission DTC's. Record all DTC's and 1 Trip Failures.
NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors. Repair as necessary.Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test for P0706 CHECK SHIFTER SIGNAL .For Gear Ratio DTC's, check and record all CVI's.Most DTC's set on start up but some must be set by driving the vehicle such that all diagnostic monitors have run.
NOTE: Verify the flash level of the transmission controller. Some problems are corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB's related to the problem.
Perform this procedure prior to Symptom diagnosis.ContinueGo To 2		 All
2 With the DRBIII®, check Transmission DTC's.
Are there any Speed Sensor DTCs present?
Yes --> Refer to the TRANSMISSION CATEGORY  and perform the appropriate symptom.
Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1 .
No --> Go To 3		 All
3 With the DRBIII®, Check the STARTS SINCE SET counter for P0712.
NOTE: This counter only applies to the last DTC set.

Is the STARTS SINCE SET counter 2 or less?
Yes --> Go To 4
No --> Go To 8		 All
4 Turn the ignition off to the lock position.
Remove the Starter Relay.
NOTE: Failure to remove Starter Relay can cause a Transmission - No Response condition.

Install the Transmission Simulator, Miller tool #8333.
NOTE: Check connectors - Clean/repair as necessary.

Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIII®, monitor the TRANS TEMP VOLTS while turning the Thermistor Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIII® readings with the numbers listed on the Transmission Simulator.
Do the readings on the Transmission Simulator match the DRBIII® readings +/- 0.2 volts?
Yes --> Go To 5
No --> Go To 6		 All
5 If there are no possible causes remaining, view repair.
Repair
Replace Transmission Solenoid/TRS Assembly per the Service Information.
Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1 .		 All
6 Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/TRS Assembly harness connector.
NOTE: Check connectors - Clean/repair as necessary.

Measure the resistance between ground and the Transmission Temperature Sensor Signal circuit.
Is the resistance below 5.0 ohms?
Yes --> Repair the Transmission Temperature Sensor Signal circuit for a short to ground.
Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1 .
No --> Go To 7		 All
7 Using the schematics as a guide, inspect the wiring and connectors. Repair as necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.
Repair
Replace the Transmission Control Module per the Service Information. WITH THE DRBIII® PERFORM QUICK LEARN .
Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1 .		 All
8 The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this circuit.
Wiggle the wires while checking for shorts and open circuits.
With the DRBIII®, check the EATX DTC EVENT DATA to help identify the conditions in which the DTC was set.
Were there any problems found?
Yes --> Repair as necessary.
Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1 .
No --> Test Complete.		 All
scientia non olet · About LEMON Manuals