LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2005 >> Wrangler Rubicon, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 490 (Powertrain Diagnostic Procedures - Diesel) >> Diagnostic Information And Procedures >> DRIVEABILITY - Diesel - Symptoms >> Symptom: *CHECKING THE ECM POWER AND GROUND CIRCUITS >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2005 Jeep Liberty. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC PROCEDURES - CHECKING THE ECM POWER AND GROUND CIRCUITS

TEST ACTION APPLICABILITY
1 Turn the ignition off.
Disconnect the ECM harness connectors.
Using a 12-volt test light connected to 12-volts, check each of the ECM ground circuits in ECM harness connector C2 cavities 2, 4 and 6.
Did the test light illuminate for each cavity?
Yes --> Go To 2
No --> Repair the ECM Ground circuit(s) for an open.
Perform ROAD TEST VERIFICATION - VER-2 .		 All
2 Turn the ignition off.
Disconnect the ECM harness connectors.
Turn the ignition to the Start position.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch (Start) Output circuit in ECM harness connector C2 cavity 22.
Is the test light on?
Yes --> Go To 3
No --> Repair the Fused Ignition Switch (Start) Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2 .		 All
3 Turn the ignition off.
Disconnect the ECM harness connectors.
Turn the ignition to the Start position.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch (Start Run Output circuit in ECM harness connector C2 cavity 19.
Turn the ignition to the Run position.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch (Start/Run) Output circuit in ECM harness connector C2 cavity 19.
Is the test light on for both ignition switch positions?
Yes --> Go To 4
No --> Repair the Fused Ignition Switch (Start/Run) Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2 .		 All
4 Turn the ignition off.
Disconnect the ECM harness connectors.
Connect a jumper wire between ground and the ASD Relay Control circuit in ECM C2 harness connector cavity 44.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the Fused ASD Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5.
Does the test light illuminate brightly for each circuit?
Yes --> Test Complete.
No --> Go To 5		 All
5 Turn the ignition off.
Remove the ASD Relay from the PDC.
Using a 12-volt test light connected to ground, check both Fused ASD Relay Battery Supply circuits in ASD Relay connector.
Is the test light on?
Yes --> Go To 6
No --> Repair the Fused ASD Relay Battery Supply circuit(s) for an open.
Perform ROAD TEST VERIFICATION - VER-2 .		 All
6 Turn the ignition off.
Disconnect the ECM harness connectors.
Remove the ASD Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 in the ASD Relay connector.
Using a 12-volt test light connected to ground, check the ASD Relay Output circuit in ECM harness connector C2 cavities 1, 3 and 5.
Did the test light illuminate for each circuit?
Yes --> Go To 7
No --> Repair the ASD Relay Output circuit(s) for an open.
Perform ROAD TEST VERIFICATION - VER-2 .		 All
7 Turn the ignition off.
Install a substitute relay in place of the ASD Relay.
Disconnect the ECM harness connectors.
Connect a jumper wire between ground and the ASD Relay Control circuit in ECM C2 harness connector cavity 44.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the Fused ASD Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5.
Did the test light illuminate for each circuit?
Yes --> Replace the ASD Relay.
Perform ROAD TEST VERIFICATION - VER-2 .
No --> Go To 8		 All
8 Turn the ignition off.
Disconnect the ECM harness connectors.
Remove the ASD Relay from the PDC.
Measure the resistance of the ASD Relay Control circuit between the PDC connector and the ECM harness connector.
Is the resistance below 10.0 ohms?
Yes --> Go To 9
No --> Repair the ASD Relay Control circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2 .		 All
9 Turn the ignition off.
Disconnect the ECM harness connectors.
Remove the ASD Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 of the ASD Relay connector in the PDC.
Turn the ignition on.
Measure the voltage on the ASD Relay Control circuit.
Is the voltage above 1.0 volt?
Yes --> Repair the ASD Relay Control circuit for a short to voltage.
Perform ROAD TEST VERIFICATION - VER-2 .
No --> Test Complete.		 All
scientia non olet · About LEMON Manuals