Transmission Verification Test

TRANSMISSION VERIFICATION TEST

TRANSMISSION VERIFICATION TEST	APPLICABILITY
Connect the DRBIII® to the Data Link Connector (DLC). Reconnect any disconnected components. With the DRBIII®, erase all Transmission DTC's, also erase the PCM DTC's. NOTE: Erase DTC P0700 in the PCM to turn the Malfunction Indicator Lamp (MIL) off after making Transmission repairs. With the DRBIII®, display Transmission Temperature. Start and run the engine until the Transmission Temperature is HOT - above 43°C or 110°F. Check the Transmission Fluid and adjust if necessary. Refer to the service information for the Fluid Fill procedure. NOTE: If the Transmission Control Module or the Transmission has been repaired or replaced it is necessary to perform the DRBIII® Quick Learn Procedure and reset the "Pinion Factor" Road test the vehicle. With the DRBIII®, monitor the engine RPM. Make 15 to 20 1-2, 2-3, 3-4 upshifts. Perform these shifts from a standing start to 45 MPH with a constant throttle opening of 20 to 25 degrees. Below 25 MPH, make 5 to 8 wide open throttle kickdowns to 1st gear. Allow at least 5 seconds each in 2nd and 3rd gear between each kickdown. For a specific DTC, drive the vehicle to the Symptom's When Monitored/When Set conditions to verify the DTC repair. If equipped with AutoStick®, up-shift and down-shift several times using the AutoStick® feature during the road test. NOTE: Use the EATX OBDII Task Manager to run Good Trip time in each gear, this will confirm the repair and to ensure that the DTC has not re-matured. Check for Diagnostic Trouble Codes (DTC's) during the road test. If a DTC sets during the road test, return to the and perform the appropriate Symptom. Were there any Diagnostic Trouble Codes (DTCs) set during the road test? Yes : Refer to the symptom list for appropriate Symptom(s). No : Repair is complete.	All

APPLICABILITY

Connect the DRBIII® to the Data Link Connector (DLC).
Reconnect any disconnected components.
With the DRBIII®, erase all Transmission DTC's, also erase the PCM DTC's.

NOTE: Erase DTC P0700 in the PCM to turn the Malfunction Indicator Lamp (MIL) off after making Transmission repairs.

With the DRBIII®, display Transmission Temperature. Start and run the engine until the Transmission Temperature is HOT - above 43°C or 110°F.
Check the Transmission Fluid and adjust if necessary. Refer to the service information for the Fluid Fill procedure.

NOTE: If the Transmission Control Module or the Transmission has been repaired or replaced it is necessary to perform the DRBIII® Quick Learn Procedure and reset the "Pinion Factor"

Road test the vehicle. With the DRBIII®, monitor the engine RPM. Make 15 to 20 1-2, 2-3, 3-4 upshifts. Perform these shifts from a standing start to 45 MPH with a constant throttle opening of 20 to 25 degrees.
Below 25 MPH, make 5 to 8 wide open throttle kickdowns to 1st gear. Allow at least 5 seconds each in 2nd and 3rd gear between each kickdown.
For a specific DTC, drive the vehicle to the Symptom's When Monitored/When Set conditions to verify the DTC repair.
If equipped with AutoStick®, up-shift and down-shift several times using the AutoStick® feature during the road test.

NOTE: Use the EATX OBDII Task Manager to run Good Trip time in each gear, this will confirm the repair and to ensure that the DTC has not re-matured.

Check for Diagnostic Trouble Codes (DTC's) during the road test. If a DTC sets during the road test, return to the and perform the appropriate Symptom.
Were there any Diagnostic Trouble Codes (DTCs) set during the road test?
1. Yes : Refer to the symptom list for appropriate Symptom(s).
2. No : Repair is complete.

All