LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2023 >> XF R-Dynamic SE >> Repair and Diagnosis >> External Pages >> Different car >> Section 251 (Automatic Transmission/Transaxle - RWD -- XE/(760)) >> Automatic Transmission/Transaxle - RWD (G1868372) >> Installation >> Transmission - INGENIUM I4 2.0L Petrol (G2046507) >> Installation >> Part(S)

Transmission - INGENIUM I4 2.0L Petrol (G2046507): Installation: Part(S)

WARNING: This page is about a different car, the 2020 Jaguar XE and 2019 Jaguar XE. However, it is still accessible from the selected car via links, so may be relevant.
STEP PART NAME QUANTITY
Step 18 Torque converter bolts 4
Step 25 Transmission fluid cooler tubes to transmission O-ring seals 1
CAUTION: New transmission assemblies are supplied pre-filled with transmission fluid.
NOTE:
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
  1. G11313993Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the 3 bolts and the toque converter transportation brace.

  2. G11313994Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Make sure the torque converter is fitted to the specification illustrated.

  3. G11313929Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the mounting.

  4. G11313903Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transmission plug.

  5. G11313902Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the emergency park release lever and the nut

    Torque  : 12Nm 

  6. G11313901Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transmission covers.

  7. G11313925Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the wiring harness.

  8. CAUTION: Care must be taken not to damage the component.
    NOTE: Make sure the electrical connector is correctly secured.
    G11314030Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    connect the plug and install clips.

  9. G11313896Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the heatshield.

    Torque  : 9Nm 

  10. G11313895Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the exhaust bracket.

    Torque  : 25Nm 

  11. CAUTION:
    • Make sure the seal is installed correctly.
    • To prevent water ingress and subsequent transmission damage, make sure that the breather is fully pushed home into the transmission casing. The white line around the circumference of the pipe should not be visible when correctly installed.
    NOTE: Remove and discard all blanking caps.
    G11313894Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transmission breather.

  12. G11313920Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transfer case mounting.

    Torque  : 48Nm 

  13. WARNING: This step requires the aid of another technician.
    CAUTION:
    • Care must be taken to avoid damaging the surrounding components.
    • Make sure that the torque converter remains in the transmission.
    NOTE: Remove and discard the tie straps securing the torque converter.
    G11313919Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transmission.

  14. G11313891Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the bolts.

    Torque  : 47.5Nm 

  15. G11313890Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the bolts.

    Torque  : 47.5Nm 

  16. G11313889Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the bolts in the correct orientation.

    Torque  : 47.5Nm 

  17. G11313915Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Using a suitable stand, support the transmission.

      General Equipment: Transmission jack 

    • Install the 4 bolts.

      Torque  : 45Nm 

  18. NOTE: Only turn the engine in the normal direction of rotation.
    G11313887Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the new torque converter bolts.

    Renew Part: Torque converter bolts  Quantity: 4. 

    Torque  : 70Nm 

  19. G11313886Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the wiring harness bracket.

    Torque  : 10Nm 

  20. G11313884Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Connect the wiring harness and the clips.

  21. G11313885Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the clips.

  22. G11313883Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    connect the electrical connector and install the bolt.

    Torque  : 10Nm 

  23. G11313882Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Secure the clips.

  24. G11313881Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Connect the emergency park release lever.

    Torque  : 11Nm 

  25. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that new O-ring seals are installed.
    NOTE: Remove and discard the blanking caps.
    G11313880Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the transmission cooler pipes.

    Renew Part: Transmission fluid cooler tubes to transmission O-ring seals  Quantity: 1. 

    Torque  : 22Nm 

  26. G11313879Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the bolt.

    Torque  : 22Nm 

  27. Install the driveshaft.

    Refer to: DRIVESHAFT - INGENIUM I4 2.0L PETROL

  28. Install the starter motor.

    Refer to: STARTER MOTOR

  29. G11313877Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the engine support beam.

  30. G11313876Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the clip.

  31. Install the cowl vent screen.

    Refer to: COWL PANEL

  32. Install the engine cover.

    Refer to: ENGINE COVER - INGENIUM I4 2.0L PETROL

  33. Connect the battery ground cable.

    Refer to: STARTUP BATTERY DISCONNECT AND CONNECT

  34. Check the transmission fluid level.

    Refer to: TRANSMISSION FLUID LEVEL CHECK 

    • If a new Transmission Assembly is installed. The Jaguar Land Rover approved diagnostic equipment must be used to calibrate the module.
    • Select 'Transmission Control Module [TCM]'
    • Select 'Replace ECU'
    • Follow all on-screen instructions to complete this task.
scientia non olet · About LEMON Manuals