Pinpoint Test I: Luggage Compartment Lid Positional Data Test
- I1: LUGGAGE COMPARTMENT LID POSITIONAL DATA TEST NOTE: Before beginning this pinpoint test it may be useful to complete Pinpoint Test S, if not already completed
- This step is still under development with the SDD team. Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - Spindle Position D911 check if the luggage compartment lid actuator position is known by the system or not. With output greater than 0x64 (hex) or greater than 100 (decimal), or alternatively if DTC C2005-31 or C2006-31 is currently active. for any of these conditions the luggage compartment lid position is unknown by the system
Is the luggage compartment lid position unknown?
Yes: GO to I2.
On the warranty claim please quote feedback ID "FID 3.6"
No: GO to I3.
On the warranty claim please quote feedback ID "FID 3.6"
- This step is still under development with the SDD team. Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - Spindle Position D911 check if the luggage compartment lid actuator position is known by the system or not. With output greater than 0x64 (hex) or greater than 100 (decimal), or alternatively if DTC C2005-31 or C2006-31 is currently active. for any of these conditions the luggage compartment lid position is unknown by the system
- I2: LUGGAGE COMPARTMENT LID BODY FITMENT CHECK
- Check the position of the luggage compartment lid relative to the aperture. Check for flushness across the back of the vehicle, both vertically and horizontally
Is the luggage compartment lid centralized both horizontally and vertically in the aperture?
Yes: GO to I3.
No: Refer to the relevant article of the repair information and reset the luggage compartment lid to achieve a good gap and flush condition across the rear of the vehicle. After resetting the luggage compartment lid according to the repair information instructions, Using the Jaguar Land Rover Approved Diagnostic Equipment, recalibrate the luggage compartment lid and retest operation
On the warranty claim please quote feedback ID "FID 3.7"
- Check the position of the luggage compartment lid relative to the aperture. Check for flushness across the back of the vehicle, both vertically and horizontally
- I3: LUGGAGE COMPARTMENT LID POSITION SENSOR CHECK
- Refer to the electrical circuit diagrams and manually moving the luggage compartment lid slowly, measure the position sensor voltage between C4PL20B-8 and C4PL20B-21 and then between C4PL20B-9 and C4PL20B-21. Repeat for second spindle, if fitted: Measure voltage between C4PL20B-6 and C4PL20B-18 and then between C4PL20B-7 and C4PL20B-18. Important: Move spindles slowly to be able to capture the transitions
Does the voltage on the position sensor alternate between ~0V and ~9V?
Yes: GO to PINPOINT TEST J .
No: GO to I4. On the warranty claim please quote feedback ID "FID 3.8"
- Refer to the electrical circuit diagrams and manually moving the luggage compartment lid slowly, measure the position sensor voltage between C4PL20B-8 and C4PL20B-21 and then between C4PL20B-9 and C4PL20B-21. Repeat for second spindle, if fitted: Measure voltage between C4PL20B-6 and C4PL20B-18 and then between C4PL20B-7 and C4PL20B-18. Important: Move spindles slowly to be able to capture the transitions
- I4: LUGGAGE COMPARTMENT LID POSITION SENSOR CHECK
- Refer to the electrical circuit diagrams
Is there continuity between the hall sensor output on the luggage compartment lid actuator and the luggage compartment lid control module end of the harness?
Yes: GO to I5.
No: Repair the circuit as necessary
On the warranty claim please quote feedback ID "FID 3.9"
- Refer to the electrical circuit diagrams
- I5: LUGGAGE COMPARTMENT LID POSITION SENSOR CHECK
- Using powered operation, ensure that the luggage compartment lid has moved in the three seconds prior to this test. Using a multimeter, check the voltage on terminal 1 of the actuator connector (Right hand actuator C4PL21B-1, Left hand actuator C4PL21A-1)
Is there ~9V present?
Yes: Refer to the relevant article of the repair information and install a new luggage compartment lid actuator as necessary
On the warranty claim please quote feedback ID "FID 3.10"
No: Using the Jaguar Land Rover Approved Diagnostic Equipment, reconfigure the luggage compartment lid control module with the latest level software
Using the Jaguar Land Rover Approved Diagnostic Equipment, calibrate the luggage compartment lid control module
If the two steps above do not remedy the failure mode, refer to the relevant article of the repair information and install a new luggage compartment lid control module as necessary
On the warranty claim please quote feedback ID "FID 3.10"
- Using powered operation, ensure that the luggage compartment lid has moved in the three seconds prior to this test. Using a multimeter, check the voltage on terminal 1 of the actuator connector (Right hand actuator C4PL21B-1, Left hand actuator C4PL21A-1)