Wheel Knuckle (G2187517): Installation

The following step(s) applies to:

All vehicles

CAUTION: Make sure that these components are installed to the noted removal position.

NOTE: Only do the following step(s) if a new component is to be installed.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Using the special tools and a hydraulic press, install the wheel bearing.

Special Tool(s): JLR-204-807, JLR-204-812

General Equipment: Hydraulic press
CAUTION: Make sure the circlip is seated in the groove correctly.

NOTE: Only do the following step(s) if a new component is to be installed.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the circlip.
NOTE: Only do the following step(s) if a new component is to be installed.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Using the special tools and a hydraulic press, install the wheel hub into the wheel bearing.

Special Tool(s): 204-726, JLR-204-836

General Equipment: Hydraulic press
CAUTION: Make sure that the new nut and bolt are installed.
- Install the wheel knuckle.
- Install and tighten the upper control arm nut and the bolt.
  Renew Part: Upper control arm retaining nut and bolt Quantity: 1 .
  
  Torque
  
  Stage 1: 40 Nm
  
  Stage 2: 180°
The following step(s) applies to:

4x4
Make sure the halfshaft is fully installed into the rear differential.
Slide the halfshaft into the wheel knuckle.
The following step(s) applies to:

All vehicles
CAUTION: Make sure that the new nut and bolt are installed.
- Secure the toe link.
- Install and tighten the nut and the bolt.
  Renew Part: Toe link to knuckle nut and bolt Quantity: 1 .
  
  Torque
  
  Stage 1: 40 Nm
  
  Stage 2: 180°
CAUTION: Make sure that the new nut and bolt are installed.

Install and tighten the lower control arm nut and the bolt.

Renew Part: Rear lower arm to knuckle nut and bolt Quantity: 1 .

Torque

Stage 1: 70 Nm

Stage 2: 240°
CAUTION: Make sure that new nuts and bolts are installed.
- Install the integral link.
- Install and tighten the 2 integral link bolts and nuts.
  Renew Part: Integral link nuts and bolts Quantity: 2 .
  
  Torque
  
  Stage 1: 48 Nm
  
  Stage 2: 60°
CAUTION: Make sure a new nut is installed.

Install and tighten the stabilizer bar link nut.

Renew Part: Stabilizer bar link retaining nut(s) Quantity: 1 .

Torque : 56 Nm
- Secure the wheel speed sensor wiring harness.
- Install and tighten the 2 bolts.
  Torque : 9 Nm
- Install the rear brake disc shield.
- Install and tighten the 3 bolts.
  Torque : 9 Nm
Install the brake disc.
Refer to: BRAKE DISC .

The following step(s) applies to:

4x4
CAUTION:
- Install the retained nut.
- Do not use air tools to install the nut. Failure to follow this instruction may result in damage to the component.
- Tighten the nut without the weight of the vehicle on the suspension.
- Apply the foot brake.
- Install and tighten the halfshaft nut.
  Torque : 175 Nm
CAUTION: Do not use air tools to remove the nut. Failure to follow this instruction may result in damage to the component.
- Apply the foot brake.
- Remove and discard the halfshaft nut.
CAUTION:
- Make sure that the new nut is installed.
- Do not use air tools to install the nut. Failure to follow this instruction may result in damage to the component.
- Tighten the nut without the weight of the vehicle on the suspension.
- Apply the foot brake.
- Install and tighten the halfshaft nut.
  Renew Part: Rear halfshaft nut Quantity: 1 .
  
  Torque
  
  Stage 1: 100 Nm
  
  Stage 2: 90°
The following step(s) applies to:

All vehicles
Install the rear wheel and tire.
Refer to: WHEEL AND TIRE .
Press the brake pedal several times, check the fluid level in the brake fluid reservoir and top-up with brake fluid if necessary.
Deactivate the service mode function of the EPB .
Refer to: ELECTRIC PARK BRAKE SERVICE MODE ACTIVATION AND DEACTIVATION .
Check the rear wheel alignment and adjust if required.