LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2021 >> XF SE >> Repair and Diagnosis >> External Pages >> Different car >> Section 58 (Engine - V6 S/C 3.0L Petrol -- XE (X760)) >> Engine - V6 S/C 3.0L Petrol >> Crankshaft Pulley >> Removal And Installation >> Removal

Removal And Installation: Removal

WARNING: This page is about a different car, the 2018 Jaguar XE and 2017 Jaguar XE. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
  1. Disconnect the startup battery ground cable.

    Refer to: Battery Disconnect And Connect and Specifications .

  2. Raise and support the vehicle on a suitable 2 post lift.

    Refer to: Lifting .

  3. Remove the cooling fan.

    Refer to: Cooling Fan Motor And Shroud

  4. Remove the starter motor.

    Refer to: Starter Motor .

  5. G11286497

    Remove the supercharger drive belt.

  6. G11286498

    Remove the accessory drive belt. Refer to ACCESSORY DRIVE BELT (Removal and Installation).

  7. G11285712
    • Install the special tool.
    • Vehicles without Auto stop/start system.

      Special Tool(s):  303-1448

    • Vehicles with Auto stop/start system.

      Special Tool(s):  JLR-303-1304

  8. G11284916

    Remove the bolts.

  9. G11284917
    • Install the special tools.
    • Special Tool(s):  303-1437
    • Special Tool(s):  303-1438
  10. G11284918

    Install the bolts.

    Torque Specification: 25 Nm 

  11. G11285712
    • Remove the special tool.
    • Vehicles without Auto stop/start system.

      Special Tool(s):  303-1448

    • Vehicles with Auto stop/start system.

      Special Tool(s):  JLR-303-1304

  12. G11284919
    • Using a suitable vehicle stand, support the special tools.
    • Special Tool(s):  303-1437
    • Special Tool(s):  303-1438
  13. NOTE: The crankshaft pulley bolt will be very tight.
    G11284920

    Remove the crankshaft pulley bolt.

  14. G11285712
    • Install the special tool.
    • Vehicles without Auto stop/start system.

      Special Tool(s):  303-1448

    • Vehicles with Auto stop/start system.

      Special Tool(s):  JLR-303-1304

  15. G11284918
    • Remove the two bolts.
  16. G11284917
    • Remove the special tools.
    • Special Tool(s):  303-1437
    • Special Tool(s):  303-1438
  17. G11284923

    Remove and discard the bolt.

  18. G11284924

    Remove the bolts.

  19. G11284925
    • Install the special tool.
    • Special Tool(s):  303-1440
  20. G11284926
    • Install the special tool.
    • Special Tool(s):  303-1441
  21. G11284927
    • Install the special tool.
    • Special Tool(s):  303-1439
  22. G11284928

    Rotate the special tool nut to remove the crankshaft pulley.

  23. NOTE: Make sure to clean the threads in the end of the crankshaft and that the crank nose is free of any foreign materials.
    G11284929
    1. Remove the crankshaft pulley.
    1. Remove and discard the friction washer.
  24. G11284930

    Remove the special tool.

  25. G11284931

    Remove the special tool.

scientia non olet · About LEMON Manuals