General Equipment

WARNING: This page is about a different car, the 2020 Jaguar XF and 2019 Jaguar XF. However, it is still accessible from the selected car via links, so may be relevant.

EQUIPMENT NAME
Hydraulic jib crane

WARNING: Be prepared to collect escaping fluids.

CAUTION: Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.

NOTE:

This procedure contains illustrations showing certain components removed to provide extra clarity.
This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.

Disconnect the startup battery ground cable.
Refer to: STARTUP BATTERY DISCONNECT AND CONNECT
Read the petrol fuel system health and safety precautions.
Refer to: PETROL AND PETROL-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS
Release fuel system pressure.
Refer to: FUEL SYSTEM PRESSURE RELEASE
Raise and support the vehicle on a suitable 2 post lift.
Refer to: LIFTING
Remove the hood.
Refer to: HOOD
Drain the cooling system.
Refer to: COOLING SYSTEM DRAINING AND VACUUM FILLING
Remove the electric cooling fan and shroud.
Refer to: ELECTRIC COOLING FAN AND SHROUD
Remove the front left halfshaft.
Refer to: FRONT HALFSHAFT
Remove the front right halfshaft.
Refer to: FRONT HALFSHAFT
Remove the transmission.
Refer to: TRANSMISSION - V6 S/C 3.0L PETROL
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the 3 coolant pipe connectors.
- Remove the coolant pipe.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the clip.
- Remove the 2 coolant hose clamps.
- Disconnect the 2 coolant hose connectors.
- Remove the coolant hose assembly.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the lower coolant hose connector.
- Reposition the lower coolant hose away from the engine.
- Remove the 2 clips.
- Disconnect the 4 coolant hose connectors to the charge air cooler.
- Remove the coolant hose assembly.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the 2 coolant hose connectors.
- Reposition the 2 coolant hoses away from the engine.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the coolant hose clamp.
- Disconnect the coolant hose connector.
- Remove the coolant hose.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the electrical connector.
- Remove the coolant hose clamp.
- Disconnect the 2 coolant hose connectors.
- Remove the coolant hose assembly.
WARNING: Be prepared to collect escaping fuel.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the 2 fuel line connectors.
- Reposition the 2 fuel lines away from the engine.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the 2 vacuum pipe connectors.
- Reposition the vacuum pipe assembly away from the engine.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the oil filler cap.
- Remove both Noise, Vibration and Harshness (NVH) covers.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Move the accessory drive belt tensioner as illustrated to release the tension from the accessory drive belt.
- Reposition the accessory drive belt away from the Air Conditioning (A/C) compressor.
- Release the accessory drive belt tensioner.
NOTE: If equipped.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the 2 retainers.
- Remove the trim panel.
NOTE: If equipped.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the clip.
- Remove the 3 retainers.
- Remove the trim panel.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the bolt.
- Release the transmission oil cooler from the bracket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the 2 bolts.
- Remove the transmission oil cooler bracket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the nut.
- Reposition the transmission oil cooler and pipe assembly away from the engine.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Disconnect the electrical connector.
- Remove the wiring harness clip.
- Remove the 3 bolts.
- Reposition the A/C compressor away from the engine.
CAUTION: Do not use excessive force to remove the component.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Release the 2 clips.
- Remove the starter motor cable cover.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the nut.
- Reposition the starter motor cable away from the engine.
Lower the vehicle.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the bolt.
- Remove the bracket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Install the special tool.
  Special Tool(s): 303-1436
- Install and tighten the bolt.
  Torque : 25 Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Install the special tool.
  Special Tool(s): 303-1435
- Install and tighten the bolt.
  Torque : 25 Nm
NOTE: If equipped

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the bolt.
- Reposition the ground cable away from the engine mounting.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine mounting nut.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine mounting nut.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine support bracket.

Special Tool(s): 303-021
CAUTION: Take care not to damage surrounding components.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Use a suitable hydraulic jib crane to remove the engine.

General Equipment: Hydraulic jib crane