LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2021 >> I-Pace SE >> Repair and Diagnosis >> Suspension >> Rear Suspension >> Rear Suspension -- I-Pace/X590 >> Rear Suspension (G2142706) >> Removal And Installation >> Wheel Knuckle - Vehicles With: Air Suspension (G2225271) >> Installation

Wheel Knuckle - Vehicles With: Air Suspension (G2225271): Installation

CAUTION: Make sure that all the nuts and bolts are tightened with the vehicle at normal ride height.
  1. NOTE: Only do the following step if a new wheel knuckle is to be installed.

    Install the rear wheel bearing to the wheel knuckle.

    Refer to: WHEEL BEARING .

  2. WARNING: This step requires the aid of another technician.
    CAUTION: Make sure that the wheel hub and halfshaft mating faces are clean and free of foreign material.
    • Install the wheel knuckle assembly.
    • Install a new upper control arm to wheel knuckle nut and bolt.

    Renew Part: Upper control arm retaining nut and bolt  Quantity: 1 

    Torque 

    Stage 1: 60Nm 

    Stage 2: 60° 

  3. Install a new lower control arm to wheel knuckle bolt.

    Renew Part: Rear lower arm to knuckle nut and bolt  Quantity: 1 

    Torque 

    Stage 1: 110Nm 

    Stage 2: 60° 

  4. CAUTION: Make sure the air spring is correctly located on the lower control arm.
    G13920444Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
  5. CAUTION: Make sure to counter hold the ball joint.
    • Attach the stabilizer bar link.
    • Install and tighten the nut.

    Renew Part: Stabilizer bar link retaining nut(s)  Quantity: 1  .

    Torque 

    Stage 1: 40Nm

    Stage 2: 45°

    • Install the 2 lower control arm links.
    • Install the 2 bolts and 2 nuts.

    Renew Part: Rear lower control arm nut and bolt  Quantity: 2 

    Torque 

    Stage 1: 48Nm

    Stage 2: 60°

    • Attach the tie-rod to the wheel knuckle assembly.
    • Install the nut and bolt.

    Renew Part: Tie-rod nut and bolt  Quantity: 1 

  8. Install the shock absorber lower nut and bolt.

    Renew Part: Shock absorber nut and bolt  Quantity: 1  .

    Torque  : 170Nm

  9. Install the height sensor link arm.
  10. CAUTION: Make sure that the components are clean and free from corrosion and foreign material.
    • Install the rear wheel speed sensor.
    • Install the wiring harness support bracket.
    • Install and tighten the 2 bolts.

    Torque  : 9Nm

    • Reposition the brake caliper wiring harness.
    • Install and tighten the bolt.

    Torque  : 9Nm

    • Install the brake disc heatshield.
    • Install and tighten the 3 bolts.

    Torque  : 9Nm

  13. Install the brake disc.

    Refer to: BRAKE DISC .

  14. CAUTION:
    • Do not use air tools to tighten the halfshaft nut. Failure to follow this instruction may result in damage to the halfshaft.
    • Make sure the halfshaft is correctly located in the wheel hub.

    Install and fully tighten the halfshaft nut removed in the removal steps.

    Torque  : 170Nm

    • Remove and discard the halfshaft nut.
    • Install and tighten a new halfshaft nut.

    Renew Part: Rear halfshaft nut  Quantity: 1 

    Torque 

    Stage 1: 175Nm

    Stage 2Loosen: 90°

    Stage 3: 100Nm

    Stage 4: 90°

  16. Install the rear wheel and tire.

    Refer to: WHEEL AND TIRE .

  17. Using Jaguar Land Rover approved diagnostic equipment, pressurize the air suspension system.

    Refer to: AIR SUSPENSION SYSTEM DEPRESSURIZE AND PRESSURIZE .

    General Equipment  : Jaguar Land Rover approved diagnostic equipment 

scientia non olet · About LEMON Manuals