LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2021 >> E-Pace SE >> Repair and Diagnosis >> Suspension >> Rear Suspension >> Rear Suspension -- E-Pace/X540 >> Rear Suspension (G1774681) >> Removal And Installation >> Wheel Knuckle (G2187517) >> Removal

Wheel Knuckle (G2187517): Removal

CAUTION:
  • The suspension arm nuts and bolts must be tightened with the suspension arms in the normal ride position. Failure to follow this instruction may result in premature failure of the bush.
  • Do not allow halfshafts to hang unsupported at one end or joint damage will occur.
  • Make sure the halfshaft Constant Velocity joint (CV) do not over articulate. Failure to follow this instruction may result in damage to the CV  .
NOTE:
  • This procedure contains some variation in the illustration depending on the vehicle specification, but essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
  • If a new wheel knuckle is installed, a new wheel bearing must be installed.

The following step(s) applies to: 

All vehicles 

  1. Before replacing the wheel knuckle, make sure to have followed the diagnosis and testing procedure.

    Refer to: SUSPENSION ARMS .

  2. Activate the service mode function of the Electric Park Brake (EPB).

    Refer to: ELECTRIC PARK BRAKE SERVICE MODE ACTIVATION AND DEACTIVATION .

  3. Raise and support the vehicle on a suitable 2 post lift.

    Refer to: LIFTING .

  4. Remove the rear wheel and tire.

    Refer to: WHEEL AND TIRE .

    The following step(s) applies to: 

    4x4 

  5. CAUTION: Do not use air tools to remove the nut. Failure to follow this instruction may result in damage to the component.
    NOTE: Retain the nut for use in the installation procedure.
    G13891519Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Apply the foot brake.
    • Remove the halfshaft nut.

    The following step(s) applies to: 

    All vehicles 

  6. Remove the brake disc.

    Refer to: BRAKE DISC .

  7. G13891520Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 3 bolts.
    • Remove the rear brake disc shield.
  8. G13891521Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 2 bolts.
    • Release the wheel speed sensor wiring harness.
  9. CAUTION: Discard the nuts and bolts.
    G13891522Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the stabilizer bar link nut.
    • Remove the 2 bolts and 2 nuts.
    • Remove the integral link.
  10. CAUTION: Discard the nut and the bolt.
    G13891523Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the lower control arm to wheel knuckle nut and the bolt.

  11. CAUTION: Discard the nut and bolt.
    G13891524Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the nut and the bolt.
    • Release the tie-rod.

    The following step(s) applies to: 

    4x4 

  12. CAUTION:
    • Make sure that the driveshaft is supported with suitable retaining straps.
    • Do not use a hammer to detach the halfshaft from the hub assembly, failure to follow this instruction may result in damage to the halfshaft.
    G13891525Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Using the special tool, press out the halfshaft from the wheel knuckle.

    Special Tool(s): 205-857 

    The following step(s) applies to: 

    All vehicles 

  13. CAUTION: Discard the nut and bolt.
    G13891526Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the upper control arm nut and the bolt.
    • Remove the wheel knuckle.
  14. NOTE: Only do the following step(s) if a new component is to be installed.
    G11305600Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Using the special tools, press out the drive flange from the wheel bearing.

    Special Tool(s): 204-726, JLR-204-836 

    General Equipment: Hydraulic press 

  15. NOTE: Only do the following step(s) if a new component is to be installed.
    G11283784Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Using a chisel, open up a gap to allow the special tool access.

    General Equipment: Vise 

    General Equipment: Chisel 

  16. NOTE: Only do the following step(s) if a new component is to be installed.
    G11283785Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the special tool.

      Special Tool(s): 204-305 

    • Using a hydraulic press, push the wheel hub out of the inner bearing race.

      General Equipment: Hydraulic press 

  17. CAUTION: Damaged components must be replaced.
    NOTE: Only do the following step(s) if a new component is to be installed.
    G11283786Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Clean and inspect the wheel hub mating face for deterioration, replace if damaged.

  18. NOTE: Only do the following step(s) if a new component is to be installed.
    G11305604Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Remove the circlip from the wheel knuckle assembly.

  19. NOTE:
    • Only do the following step(s) if a new component is to be installed.
    • Note the orientation of the component prior to removal.
    G11305605Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Using the special tool and a hydraulic press, remove the wheel bearing.

    Special Tool(s): 204-726 

    General Equipment: Hydraulic press 

  20. CAUTION: Damaged components must be replaced.
    NOTE: Only do the following step(s) if a new component is to be installed.
    G11305606Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Clean and inspect the wheel knuckle mating face for deterioration, replace if damaged.

scientia non olet · About LEMON Manuals