Transmission - INGENIUM I4 2.0L Petrol (G2044698): Installation: Part(S)

WARNING: This page is about a different car, the 2020 Jaguar XE and 2019 Jaguar XE. However, it is still accessible from the selected car via links, so may be relevant.

STEP	PART NAME	QUANTITY
Step 19	Torque converter bolts	4
Step 26	Transmission fluid cooler tubes to transmission O-ring seals	2

CAUTION: New transmission assemblies are supplied pre-filled with transmission fluid.

NOTE:

This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
This procedure contains illustrations showing certain components removed to provide extra clarity.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the 3 bolts and the torque converter transportation brace.
CAUTION: Apply grease of the correct specification to the torque converter spigot.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Make sure the torque converter is fitted with the measurements as show.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transmission plug.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the emergency park release lever and the nut.

Torque : 12Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transmission covers.
CAUTION:
- Make sure that the mating faces are clean and free of foreign material.
- Apply grease of the correct specification to the input shaft.
- Make sure the transfer case bolts are installed in the correct orientation.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transfer case and the bolts.

Refer to: SPECIFICATIONS

Torque : 43Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the wiring harness.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Connect the plug and install clips.
CAUTION: Care must be taken not to damage the component.

NOTE: Make sure the electrical connector is correctly secured.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the electrical connector and secure the 3 clips.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the heatshield.

Torque : 9Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the exhaust bracket.

Torque : 25Nm
CAUTION:
- Make sure the seal is installed correctly.
- To prevent water ingress and subsequent transmission damage, make sure that the breather is fully pushed home into the transmission casing. The white line around the circumference of the pipe should not be visible when correctly installed.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transmission breather.
NOTE: Do not fully tighten at this stage.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transfer case mounting finger tight.
WARNING: This step requires the aid of another technician.
CAUTION:
- Make sure that the transmission is secured with suitable retaining straps.
  - Care must be taken to avoid damaging the surrounding components.
  - Make sure that the torque converter remains in the transmission.
NOTE: Remove and discard the tie straps securing the torque converter.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transmission.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the bolts.

Torque : 48Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the bolts.

Torque : 48Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the bolts in the correct orientation.

Torque : 48Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Using a suitable stand, support the transmission.
  General Equipment: Transmission jack
- Install the 5 bolts.
  Torque : 45Nm
- Fully tighten the transfer case mounting bolt shown in step 13 .
  Torque : 48Nm
NOTE: Only turn the engine in the normal direction of rotation.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install 4 new torque converter bolts.

Renew Part: Torque converter bolts Quantity: 4 .

Torque : 65Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the wiring harness bracket.

Torque : 10Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Connect the wiring harness and the clips.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the clips.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Connect the electrical connector and install the bolt.

Torque : 10Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Secure the clips.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Connect the emergency park release lever.

Torque : 11Nm
CAUTION:
- Be prepared to collect escaping fluids.
- Make sure that new O-ring seals are installed.
NOTE: Remove and discard the blanking caps.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the transmission cooler pipes.

Renew Part: Transmission fluid cooler tubes to transmission O-ring seals Quantity: 2 .

Torque : 22Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the bolt.

Torque : 22Nm
Install the driveshaft.
Refer to: DRIVESHAFT - INGENIUM I4 2.0L PETROL
Install the starter motor.
Refer to: STARTER MOTOR
Install the front driveshaft.
Refer to: FRONT DRIVESHAFT
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the breather nuts

Torque : 22Nm
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the engine support beam.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the clip.
Install the cowl panel.
Refer to: COWL PANEL
Install the engine cover.
Refer to: ENGINE COVER - INGENIUM I4 2.0L PETROL
Connect the startup battery ground cable.
Refer to: STARTUP BATTERY DISCONNECT AND CONNECT
Check the transmission fluid level.
Refer to: TRANSMISSION FLUID LEVEL CHECK
- If a new Transmission Assembly is installed. The Jaguar Land Rover approved diagnostic equipment must be used to calibrate the module.
- Select 'Transmission Control Module [TCM]'
- Select 'Replace ECU'
- Follow all on-screen instructions to complete this task.