Pinpoint Test E: Transmission Shift Quality

WARNING: This page is about a different variant/trim than selected.

E1: DIAGNOSTIC TROUBLE CODE CHECK
1. Using the JLR approved diagnostic equipment, perform routine - Read DTC . Check for DTC in the following control modules:
  - Transmission Control Module (TCM)
  Are there DTC in the above modules?
  
  Yes: Refer to the relevant DTC index and perform the relevant corrective actions. Perform a road test and re-assess the quality of the gear shift. If the gear shift concern is still present GO to PINPOINT TEST F . If the gear shift concern has now been corrected return the vehicle to the customer.
  
  No: GO to PINPOINT TEST F .

POSSIBLE CAUSE	CLUSTER OF DTC	SYSTEM/MODULE TO INVESTIGATE
Software Calculation	P0501-86 - Vehicle Speed Sensor "A" Circuit Range/Performance Signal Invalid P0730-00 - Incorrect Gear Ratio no sub type information P1935-86 - Brake Switch/Sensor Signal Signal Invalid P2638-67 - Torque Management Feedback Signal A Range/Performance signal incorrect after event	TCM
TCM Communications	U0401-64 - Invalid Data Received from ECM/PCM A Signal Plausibility Failure U0415-86 - Invalid Data Received From Anti-Lock Brake System (ABS) Control Module Signal Invalid	PCM /ABS
TCM /Mechatronic Valve Block	P0218-98 - Transmission Fluid Temperature Sensor "A" Over Temperature Condition Component Or System Over Temperature P0613-98 - TCM Processor Component Or System Over Temperature P0720-12 - Output Shaft Speed Sensor Circuit circuit short to battery P0722-14 - Output Shaft Speed Sensor Circuit No Signal Circuit Short To Ground Or Open P272C-15 - Park Pawl Motor Control Circuit Circuit Short To Battery Or Open P0721-64 - Output Shaft Speed Sensor Circuit Range/Performance signal plausibility failure P0745-15 - Pressure Control Solenoid "A" Circuit Short To Battery Or Open P0748-15 - Pressure Control Solenoid "A" Electrical Circuit Short To Battery Or Open P2544-86 - Torque Management Request Input Signal A Signal Invalid P2545-86 - Torque Management Request Input Signal A Range/Performance signal invalid P2546-86 - Torque Management Request Input Signal A Low signal invalid	TCM
Torque Converter/Mechatronic Valve Block	P2759-15 - Torque Converter Clutch Pressure Control Solenoid Electrical Circuit Short To Battery Or Open	TCM
Torque Converter/Transmission Assembly	P0741-07 - Torque Converter Clutch Solenoid Circuit Performance/Stuck Off Mechanical Failures	TCM
Transmission Assembly	P0729-07 - Gear 6 Incorrect Ratio Mechanical Failures P0731-07 - Gear 1 Incorrect Ratio Mechanical Failures P0732-07 - Gear 2 Incorrect Ratio Mechanical Failures P0733-07 - Gear 3 Incorrect Ratio Mechanical Failures P0734-07 - Gear 4 Incorrect Ratio Mechanical Failures P0735-07 - Gear 5 Incorrect Ratio Mechanical Failures P0736-07 - Reverse Incorrect Ratio Mechanical Failures P076F-07 - Gear 7 Ratio Incorrect Mechanical Failures P07D9-07 - Gear 8 Incorrect Ratio Mechanical Failures P07DC-07 - Incorrect Shift from Gear 1 Mechanical Failures P07DD-07 - Incorrect Shift from Gear 2 Mechanical Failures P07DE-07 - Incorrect Shift from Gear 3 Mechanical Failures P07DF-07 - Incorrect Shift from Gear 4 Mechanical Failures P07E0-07 - Incorrect Shift from Gear 5 Mechanical Failures P07E1-07 - Incorrect Shift from Gear 6 Mechanical Failures P07E2-07 - Incorrect Shift from Gear 7 Mechanical Failures P07E3-07 - Incorrect Shift from Gear 8 Mechanical Failures P177A-07 - Transmission Friction Element A or B Mechanical Failures P177B-07 - Transmission Friction Element A or C Mechanical Failures P177C-07 - Transmission Friction Element A or D Mechanical Failures P177D-07 - Transmission Friction Element A or E Mechanical Failures P177E-07 - Transmission Friction Element B or C Mechanical Failures P177F-07 - Transmission Friction Element B or D Mechanical Failures P178A-07 - Transmission Friction Element B or E Mechanical Failures P178B-07 - Transmission Friction Element C or D Mechanical Failures P178C-07 - Transmission Friction Element C or E Mechanical Failures P178D-07 - Transmission Friction Element D or E Mechanical Failures P2700-07 - Transmission Friction Element A Apply Time Range/Performance Mechanical Failures P2701-07 - Transmission Friction Element B Apply Time Range/Performance Mechanical Failures P2702-07 - Transmission Friction Element C Apply Time Range/Performance Mechanical Failures P2703-07 - Transmission Friction Element D Apply Time Range/Performance Mechanical Failures P2704-07 - Transmission Friction Element E Apply Time Range/Performance Mechanical Failures	TCM
Automatic Transmission Fluid Cooling	P2783-98 - Torque Converter Temperature Too High Component Or System Over Temperature P2787-4B - Clutch Temperature Too High over temperature	TCM
Vehicle Configuration	P0721-22 - Output Shaft Speed Sensor Circuit Range/Performance Signal Amplitude > Maximum	TCM