Fuel Pump - Without High Pressure Exhaust Gas RECIRCULATION System (G2300840): Removal

WARNING: This page is about a different car, the 2019 Jaguar XE. However, it is still accessible from the selected car via links, so may be relevant.

WARNING:

Be prepared to collect escaping fuel.
Wait for a minimum of 1 minute after the engine has stopped before carrying out any repair to the fuel injection system.

CAUTION:

Before disconnecting or removing components, make sure the area around the joint faces and connections are clean. Plug open connections to prevent contamination.
Make sure that the area around the component is clean and free of foreign material.
Before disconnecting any components, make sure the area is clean and free from foreign material. When disconnected all openings must be sealed.

NOTE: This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.

Disconnect the battery ground cable.
Refer to: STARTUP BATTERY DISCONNECT AND CONNECT
Remove the engine cover.
Refer to: ENGINE COVER - INGENIUM I4 2.0L DIESEL
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the noise, vibration and harshness (NVH) material
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the fuel lines.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the fuel rail fuel supply line.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the blanking caps.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the oil level indicator bracket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the fuel supply and return lines.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the blanking caps.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the clip.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the gasket and O-ring seal.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the fuel pump fuel supply line.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the blanking cap.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the fuel pump fuel return line.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the blanking caps.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the electrical connectors.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Disconnect the electrical connector.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the exhaust gas recirculation (EGR) valve pipe.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the gasket.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the EGR valve and position to one side.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the wiring harness.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the fuel rail fuel supply line from the fuel rail.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the blanking cap.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the fuel line retaining bracket bolt.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the fuel rail fuel supply line from the fuel pump.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the blanking cap.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the fuel rail high pressure supply pipe.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the 2 bolts.
- Remove the fuel pump sprocket access cover.
- Remove and discard the fuel pump sprocket access cover seal.
NOTE: Only rotate the crankshaft clockwise.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Make sure that the alignment mark is at the 8 o'clock position, to aid correct installation of the special tool.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove the components from the special tool to aid installation of the special tool.

Special Tool(s): JLR-303-1627
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Install the special tool.

Special Tool(s): JLR-303-1627

Torque : 10Nm
CAUTION: Make sure that the special tool is correctly located.

NOTE: Only rotate the crankshaft clockwise.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Rotate the engine and align the special tool to the fuel pump gear.

Special Tool(s): JLR-303-1627
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Fully install the special tool bolts.

Special Tool(s): JLR-303-1627
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the fuel pump sprocket retaining nut.

Special Tool(s): JLR-303-1627
CAUTION: Do not remove the retaining bolts at this stage.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Loosen the bolts as indicated in the illustration.
CAUTION: Do not remove the retaining bolt at this stage.

Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Loosen the bolt as indicated in the illustration.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Rotate the special tool to break the taper on the fuel pump shaft.

Special Tool(s): JLR-303-1627
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Detach the fuel pump until it stops on the retaining bolts.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the retaining bolts.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Remove and discard the retaining bolt.
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
- Remove the fuel pump.
- Remove and discard the fuel pump seal.