Left Engine Mount (G1817157): Installation

The following step(s) applies to: 

All vehicles

1. NOTE: Make sure that the component is installed to the noted position in the removal steps.

   Install the engine mount in the correct position.

2. Install the engine mount bracket and tighten the 4 bolts to the correct torque.

   Torque  : 60Nm 

3. Install the 2 engine mount retaining bolts and tighten to the correct torque.

   Torque  : 47Nm 

4. 1. Install the left engine mount nut finger tight at this stage.
   2. Install the ground cable.

      Torque  : 20Nm 

5. Remove the hydraulic jack from under the vehicle.

   General Equipment: Hydraulic floor jacks (2 tonnes minimum capacity) 

6. Install the vacuum pipe onto the engine mount assembly.

7. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

   Loosen the right engine mount nut.

8. Raise the vehicle on the ramp.
9. WARNING: Observe due care when working near a hot exhaust system.

   Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

   Loosen the Diesel Particulate Filter (DPF) fasteners.

   The following step(s) applies to: 

   Vehicles with All Wheel Drive (AWD)

10. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Loosen the transmission mount fasteners.

    The following step(s) applies to: 

    Vehicles with Rear Wheel Drive (RWD)

11. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Loosen the transmission mount fasteners.

    The following step(s) applies to: 

    All vehicles

12. WARNING: Observe due care when working near a hot exhaust system.

    Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Loosen the exhaust clamp.

13. Lower the vehicle on the ramp.
14. 1. To align the exhaust, follow the steps below.
    2. Start and stop the engine 4 times.
    3. Start the engine.
    4. Raise the engine Revolutions Per Minute (RPM) to between 3000 RPM  and 4000 RPM  - Repeat this 5 times.
    5. Stop the engine.
    6. Start and stop the engine 5 times.

15. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Tighten the right engine mount nut.

    Torque  : 60Nm 

16. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Tighten the left engine mount nut.

    Torque  : 60Nm 

17. Raise the vehicle on the ramp.

    The following step(s) applies to: 

    Vehicles with All Wheel Drive (AWD)

18. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Tighten the transmission mount fasteners.

    Torque  : 60Nm 

    The following step(s) applies to: 

    Vehicles with Rear Wheel Drive (RWD)

19. Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Tighten the transmission mount fasteners.

    Torque  : 60Nm 

    The following step(s) applies to: 

    All vehicles

20. WARNING: Observe due care when working near a hot exhaust system.

    Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Tighten the DPF  fasteners.

    Torque  : 25Nm 

21. WARNING: Observe due care when working near a hot exhaust system.

    Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Tighten the exhaust clamp.

    Torque  : 55Nm 

22. Install the engine undershield.

    Refer to: ENGINE UNDERSHIELD