LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2019 >> XF S >> Repair and Diagnosis >> External Pages >> Different car >> Section 150 (Engine - V6 S/C 3.0L Petrol -- XE/(760)) >> Engine - V6 S/C 3.0L Petrol (G2289428) >> Removal And Installation >> Upper Timing Cover (G2385450) >> Installation

Upper Timing Cover (G2385450): Installation

WARNING: This page is about a different car, the 2019 Jaguar XE. However, it is still accessible from the selected car via links, so may be relevant.
  1. CAUTION:
    • Use only a plastic scraper when removing the sealing material.
    • Make sure that the mating faces are clean and free of foreign material.
    • Make sure that the Jaguar Land Rover approved cleaning fluid (Loctite 7063) is used to clean the mating faces.
    G13879256Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Make sure that all traces of the old sealant are removed from the mating surfaces.
    • Lubricate the camshaft cover gasket with clean engine oil.

      Refer to: SPECIFICATIONS 

  2. NOTE: Only complete this step if this component was previously removed.
    G13904036Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install 2 new CMP O-ring seals.

      Renew Part: Camshaft position sensor O-ring seal Quantity: 2. 

    • Lubricate the 2 O-ring seals with new engine oil.

      Refer to: SPECIFICATIONS 

    • Install the 2 CMP  s.
    • Install and tighten the 2 bolts.

      Torque  : 10Nm 

  3. CAUTION: Make sure that the mating faces are clean and free of foreign material.
    G13904039Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Apply a 3mm diameter bead of sealant to the area illustrated, tighten the bolts within 7 minutes.

    Refer to: SPECIFICATIONS 

  4. CAUTION: Make sure the camshaft cover gasket is fully visible, is not damaged and is seated correctly as illustrated.
    G13879258Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the upper timing cover.
    • Install, but do not fully tighten the 8 bolts.
  5. Fig 1: Upper Timing Cover Tightening Sequence
    G13879259Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install and tighten the 8 bolts in the sequence illustrated.

    Torque  : 13Nm 

    • Install the 2 VCT  solenoids.
    • Install and tighten the 4 bolts.

      Torque  : 12Nm 

    • Install the right accessory drive belt pulley.
    • Install and tighten the bolt.

      Torque  : 48Nm 

  8. Install the right accessory drive belt pulley cap.
    • Install the wiring harness.
    • Install and tighten the bolt.

      Torque  : 10Nm 

    • Install the 2 wiring harness clips.
    • Connect the 4 electrical connectors.
  10. CAUTION:
    • Use only a plastic scraper when removing the sealing material.
    • Make sure that the mating faces are clean and free of foreign material.
    • Make sure that the Jaguar Land Rover approved cleaning fluid (Loctite 7063) is used to clean the mating faces.
    G13879260Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Make sure that all traces of the old sealant are removed from the mating surfaces.
    • Lubricate the camshaft cover gasket with clean engine oil.

      Refer to: SPECIFICATIONS 

  11. NOTE: Only complete this step if this component was previously removed.
    G13904030Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install 2 new CMP  O-ring seals.

      Renew Part: Camshaft position sensor O-ring seal Quantity: 2. 

    • Lubricate the 2 O-ring seals with new engine oil.

      Refer to: SPECIFICATIONS 

    • Install the 2 CMP  s.
    • Install and tighten the 2 bolts.

      Torque  : 10Nm 

  12. CAUTION: Make sure that the mating faces are clean and free of foreign material.
    G13879261Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Apply a 3mm diameter bead of sealant to the area illustrated, tighten the bolts within 7 minutes.

    Refer to: SPECIFICATIONS 

  13. CAUTION: Make sure the camshaft cover gasket is fully visible, is not damaged and is seated correctly as illustrated.
    G13879262Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Install the upper timing cover.
    • Install, but do not fully tighten the 8 bolts.
  14. G13879263Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install and tighten the 8 bolts in the sequence illustrated.

    Torque  : 13Nm 

    • Install the 2 VCT  solenoids.
    • Install and tighten the 4 bolts.

      Torque  : 12Nm 

    • Install the left accessory drive belt pulley.
    • Install and tighten the bolt.

      Torque  : 48Nm 

  17. Install the left accessory drive belt pulley cap.
    • Install the wiring harness.
    • Install and tighten the bolt.

      Torque  : 10Nm 

    • Install the wiring harness clip.
    • Connect the 4 electrical connectors.
  19. Install the HP  fuel rail supply line.

    Refer to: FUEL RAIL SUPPLY PIPE

  20. Install the electric thermostat.

    Refer to: ELECTRIC THERMOSTAT

  21. Install the accessory drive belt.

    Refer to: ACCESSORY DRIVE BELT

  22. Connect the startup battery ground cable.

    Refer to: STARTUP BATTERY DISCONNECT AND CONNECT

scientia non olet · About LEMON Manuals